684269

McCulloch B33 PS Manual

18
Zoom out
Zoom in
Previous page
1/504
Next page
To make the fuel mixture
Note: Always use a clean fuel container when you mix
the fuel.
Note: Do not make more than 30 days quantity of fuel
mixture.
1. Add half of the gasoline quantity.
2. Add the full quantity of oil.
3. Shake the fuel mixture to mix the contents.
4. Add the remaining gasoline quantity.
5. Shake the fuel mixture to mix the contents.
6. Fill the fuel tank.
To add fuel
• Always use a fuel container with an antispill valve.
• If there is some fuel on the container, remove the
unwanted fuel and let the container dry.
• Make sure that the area near the fuel tank cap is
clean.
• Shake the fuel container before you add the fuel
mixture to the fuel tank.
To start and stop
To start a cold engine
(Fig. 47)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and then pull the throttle
trigger (C).
3. While the throttle trigger is engaged, push the fast
idle button (D).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb 10 times. The bulb does not
need to be completely filled. (Fig. 48)
6. Move the choke control to the full choke position.
(Fig. 49)
7. Hold the body of the machine on the ground with the
left hand. (Fig. 50)
8. Pull out the cord slowly with your right hand until you
feel some resistance.
9. Pull the starter cord quickly and powerfully. Repeat
approximately 5 times or until the engine attempts to
start.
10. Move the choke control to the no choke position.
11. Pull the starter cord quickly and powerfully until the
engine starts.
12. Let the engine run for 10 seconds.
13. Pull the throttle trigger to run at low speed for 60
seconds.
To start a warm engine
Note: Obey this procedure when you start a product that
has run out of fuel and has been refueled.
(Fig. 47)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and then pull the throttle
trigger (C).
3. While the throttle trigger is engaged, push the fast
idle button (D).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb 10 times. The bulb does not
need to be completely filled. (Fig. 48)
6. Hold the body of the machine on the ground with the
left hand. (Fig. 50)
7. Move the choke control to the no choke position.
8. Pull out the cord slowly with your right hand until you
feel some resistance.
9. Pull the starter cord quickly and powerfully until the
engine starts.
To stop the product
• Push the stop switch to stop the engine.
To start the engine when the fuel is too hot
If the product does not start, the fuel can be too hot.
Note:
Always use new fuel and decrease the operation
time during warm weather.
1. Put the product in a cool area away from open
sunlight.
2. Let the product cool down for 20 minutes at
minimum.
3. Press the primer bulb again and again for 10-15
seconds.
4. Obey the procedure to start a cold engine. Refer to
To start a cold engine on page 18
.
MAINTENANCE
WARNING: Read and understand the safety
chapter before you clean, repair or do
maintenance on the product.
Maintenance schedule
Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use the
product each day. Only do the maintenance work that is
18 860 - 001 - 28.10.2018
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch B33 PS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch B33 PS in the language / languages: All languages as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info