684269

McCulloch B33 PS Manual

17
Zoom out
Zoom in
Previous page
1/504
Next page
To assemble the trimmer attachment
1. Attach the cutting attachment guard (A), braces (B),
washers (C), washers (D), and screws (E). Fully
tighten the screws. (Fig. 37)
2. Insert the hex wrench (A) to prevent rotation of the
shaft.
3. Remove the nut (B), support cup (C) and holder (D)
on the trimmer and brushcutter attachment. (Fig. 38)
4. Tighten the trimmer head (B) onto the shaft. (Fig. 39)
To assemble the brushcutter
attachment
1. Attach the cutting attachment guard (A), braces (B),
washers (C), washers (D), and screws (E). Fully
tighten the screws. (Fig. 37)
2. Insert the hex wrench (A) to prevent rotation of the
shaft.
3. Remove the nut (B), support cup (C) and holder (D)
on the trimmer and brushcutter attachment. (Fig. 40)
4. Attach the blade (B), bottom holder (C), support cup
(D), and nut (E). Fully tighten the nut. (Fig. 41)
To assemble the pole saw
attachment
See
To do the maintenance on the pole saw attachment
on page 20
for assembly instructions for the pole saw
attachment.
To assemble the two-piece shaft
1. Turn the knob to loosen the shaft coupling. (Fig. 42)
2. Move the locking/release button (A) into the guide
recess. Push the attachment into the coupler until
the locking/release button sets into the primary hole
(B). (Fig. 43)
3. Insert the shaft into the shaft coupling. The button
must go through the hole.
Note: If the attachment does not go fully into the
upper shaft, use the combination tool to push the
internal drive shaft deeper into the tube. It can be
necessary to turn the combination tool while you
push.
4. Make sure that you fully tighten the knob before you
operate the product. (Fig. 44)
To disassemble the two-piece shaft
1. Turn the knob to loosen the shaft coupling. (Fig. 45)
2. Push and hold the locking/release button (B). Pull
the shafts apart. (Fig. 46)
OPERATION
WARNING: Read and understand the safety
chapter before you operate the product.
Fuel
To use fuel
CAUTION: This product has a two-cycle
engine. Use a mixture of gasoline and two-
cycle engine oil. Make sure to use the
correct quantity of oil in the mixture.
Incorrect ratio of gasoline and oil can cause
damage to the engine.
Gasoline
CAUTION: Do not use gasoline with an
octane number less than 90 RON (87 AKI).
This can cause damage to the product.
CAUTION: Do not use gasoline with more
than 10% ethanol concentration (E10). This
can cause damage to the product.
• Always use new unleaded gasoline with a minimum
octane number of 90 RON (87 AKI) and with less
than 10% ethanol concentration (E10).
• Use gasoline with a higher octane number if you
frequently use the product at continuously high
engine speed.
Two-cycle engine oil
• Use only high quality two-cycle engine oil. Use only
an air cooled engine oil.
• Do not use other types of oil.
• Mixture ratio 50:1 (2%)
Petrol, litre Two-stroke oil, litre
5 0.10
10 0.20
15 0.30
20 0.40
860 - 001 - 28.10.2018 17
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch B33 PS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch B33 PS in the language / languages: All languages as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info