684239
10
Zoom out
Zoom in
Previous page
1/27
Next page
English---10
115430026 Rev. 4 2/17/12
ASSEMBLY
NOTE: Make sure unit is assembled cor-
rectly as shown in this manual.
Fittin g the h andlebar
S Remove the screw at the rear of the
throttle handle.
S Slide the throttle handle onto the right
side of the handlebar (see illustration).
S Align the screw hole in the throttle han-
dle with the hole in the handlebar .
S Refit the screw in the hole in the rear of
the throttle handle.
S Screw the screw through the handle and
handlebar. Tighten the screw.
S Fit the mounting components as shown.
S The handlebar mounting must be fitted
between the arrows on the shaft.
S Tighten the screws with a hex wrench.
Fittin g the harness
Proper harness and handlebar adjust-
ments must be made with the engine com-
pletely stopped before using unit.
Fitting the harness clamp
S Place the upper harness clamp over the
shaft and position the lower harness
clamp under the shaft. Align the upper
and lower clamp screw holes. Clamp
must be fitted above the arrow on the
shaft
(
see illustration
)
.
Adjusting the harness
S At the front of the harness is an easily
accesible quick release. Use the quick
release in any emergency situation that
requires you to free yourself from the
machine and harness.
Spreading the load on your
shoulders
S A well--adjusted harness and machine
makes work much easier.
S Put on the harness. Adjust the harness
for the best working position. Tension the
side straps so that the weight is evenly
distributed across both shoulders.
NOTE: It may be necessary to relocate
the harness clamp on the shaft for proper
balancing of unit.
W ARNING: When using a
brushcutter, it must always be
hooked securely to the harness.
Otherwise, you will be unable to
control the brushcutter safely.
This can result in injury to yourself
or others. Never use a harness with
a defective quick release.
N
O
TE: Fit throttle wire in groove o
f
lower
harness clamp before tightening screws.
S Insert two screws into the screw holes.
S Secure harness clamp by tightening
screws with a hex wrench.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch B28 B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch B28 B in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info