634684

Mc crypt DJ-40 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
38
9. Raccordement
Exemple de raccordement :
1 Ampli cateur 2 Lecteur de disques
3 Lecteur CD 4 Composant réseau à che
5 Ampli cateur
Ne faites fonctionner l'appareil que si vous vous être familiarisé avec ses fonctions et cette notice d'utilisation. Véri ez
encore une fois tous les raccordements. N'écoutez pas de la musique pendant des périodes prolongées avec un niveau
sonore trop élevé ; cela est particulièrement valable lorsque vous utilisez un casque. Si le volume du son est trop élevé,
l'audition est endommagée.
OUTPUT
INPUT
PHONO1
LINE1PHONO2
LINE2
AC 9V
1000mA
ON
POWER
OFF
L
R
CH2 CH1
GND GND
AB
AA
AC
A
A A
AA
SENOHPDAEHCIM
B
C
C
L
R
1
22
33
4
5
23
8. Installing the device
Make sure when mounting on a desk with other equipment that there is suf cient ventilation. Do not place the device on
a soft surface such as, for example, a carpet or a bed etc.
In addition, air circulation must not be obstructed by objects such as magazines, tablecloths or curtains. This can
prevent dissipation of heat from the device and can lead to overheating ( re hazard). To ensure adequate ventilation,
there must be 5 cm of free space around the plug-in power unit.
Do not drill any holes or screws into the product in order to attach the device somewhere as this may damage it and
impair its safety.
When setting up the device, make sure that it has a secure footing and is on a stable surface as people could be injured
if the mixer fell down.
When setting up the device, make sure that the connection cable is not being pinched or damaged by any sharp edges.
Always lay the cables so that no-one can trip over them or become entangled in them. Risk of injury!
When selecting a location to set up the mixer, make sure it will not be exposed to direct, intensive sunlight, vibration,
dust, heat, cold or humidity. No other appliances with strong electric or magnetic elds, for example transformers,
engines, cordless telephones, radios or PCs may be located in the direct vicinity of the mixer as these could affect it.
The mixer is suitable for installation in a desk and as a table device. There are 4 mounting holes in the upper covering board for fastening when
mounting on a desk.
Make sure when mounting on a desk with other equipment that there is suf cient ventilation. Do not drill any additional
holes or screw any additional screws into the housing to mount the device as this will damage the device. Make sure that
the device is set up on a secure and stable surface. In view of the variety of varnishes and polishes used for furniture, the
base of the device might leave visible marks on the furniture it is placed on as a result of a chemical reaction. Therefore
the device should not be placed on valuable furniture without suf cient protection.
9. Connection
Prior to connection, disconnect the mixing table and all other devices to be connected to the mixing table from the mains (pull the power
plugs).
For connection to the cinch outputs and inputs, only use suitably screened cinch cables. Only use a suitable microphone cable for
connecting the microphone input. Using other cables may lead to disruptions. In order to avoid distortions or maladjustment that
may lead damages to the device, you may only connect the audio outputs of playback devices with cinch level to the cinch inputs,
respectively only the cinch inputs of an audio device to the cinch outputs of the mixing table. Please also observe the connection
values listed in the “Technical Data”.
9.1. Connecting the inputs
The following applies for all cinch inputs:
The white cinch jack of the mixer is the input for the left channel.
The red cinch jack of the mixer is the input for the right channel.
Inputs LINE1 (20) and LINE2 (17)
Two LINE inputs are available. You can connect your tuner, CD player, MP3 player etc. to these stereo cinch inputs.
No high-level sources such as tuners, CD players or similar may be connected to the PHONO inputs as this will overload the input.
Short-circuit plugs are inserted in the PHONO input jacks. Leave these plugs inserted when you are not using the PHONO input
concerned. The short-circuit plugs prevent buzzing occurring via the PHONO inputs.
Inputs PHONO1 (21) and PHONO2 (18)
Two PHONO inputs are available. You can connect your turntable to these stereo cinch inputs. The PHONO inputs are designed for turntables
with a magnet system.
Earth screw terminals (19)
If your turntable has its own earth (usually a thin, black cable with clamp-type socket), connect this to the earth terminals. This helps to avoid
buzzing.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mc crypt DJ-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mc crypt DJ-40 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info