346835
6
Zoom out
Zoom in
Previous page
1/28
Next page
Installation
Full-Length Aluminum Handles
To Install:
1. Releasetop door trim by removing Phillips
screws from top of fresh food door and
retain screws for later use.
,
Align notches on back of handle
with retaining clips on doors. Insert
clips into notches and slide handle
down until it contacts bottom trim.
3. Replace top door trim and Phillips screws.
Door Clip
.
To Remove:
1. Releasetop door trim by removing
Phillips screws from top of fresh food
door and retain screws for later use.
2. Grasp handle firmly with both hands.
Slide handle upward approximately 1.9
cm to release.
3. Repeat instructions 1-3 to remove
other handle.
Repeat instructions 1-3 to install other handle.
To Reinstall:
1. Repeat in reverse order.
6 mm Panel Dimensions:
ExtendedDoor Models
Freshfooddoor
Upperfreezerdoor (dispenser)
Lowerfreezerdoor(dispenser]
Freezerdoor (non-dispenser)
To Install:
1.
,
3.
,
6.
Panel Height
169.5 cm
46.0 cm
81.5 cm
169.5 cm
Remove top trim screws with a Phillips
screwdriver to remove top trim.
Slide handle upward until loose. Pull handle from door.
Remove door retainer clips with a V;' hex
head driver.
PanelWidth
48.1crn
35.4cm
35.4cm
35.4cm
Slide bottom of panels into bottom door trim until hinge side
of decorator panel rests under hinge side trim. Important:
Tape tops of panels to door to prevent panels from falling.
Reinstall door retainer clips with a '/;' hex head driver.
Reinstall handle by inserting retaining clips on door into
notches on back of handle. Slide handle down until it contacts
bottom trim.
7. Remove tape from tops of panels before
reinstalling top door trim with Phillips screw
removed in step 1.
To Remove:
1. Perform step 1 as explained in the installation instructions.
Important: Tapetops of panels to door to prevent panels from
falling.
2. Perform steps 2 & 3. Remove tape to slide panels out of door
trim. Continue with steps 5, 6, and 7 to replace handle and
trim.
Euro Handles
Decorator Door Panels
Procedure:
To protect door surfaces from being scratched, cover back
edges of decorator panels by placing masking tape along
back edges.
Saveall screws and reuse in original locations.
This handle style is installed at the factory.
Materials Needed:
_2"Allen wrench
To Remove:
Remove set screw from handle
mounting post using _2"Allen wrench.
Repeat the procedure on all posts to remove the handle.
To Replace:
Align handle with the mounting posts.
Fully tighten all set screws to secure handle in place.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maytag gc2227 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maytag gc2227 in the language / languages: English as an attachment in your email.

The manual is 4,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info