346835
28
Zoom out
Zoom in
Previous page
1/28
Next page
Troubleshooting
ii !i Uliii iii !i !i iil
Ice forms in inlet Water pressure is low. Water pressure must be between 241 to 689 kpa to
tube to ice maker function properly.
Saddle valve not open completely.
Freezer temperature is too high.
Refrigerator is Supply tubing was used to complete
leaking water water connection.
Improper water valve was installed.
Water flow is Water pressure is low.
slower than normal
Saddle valve not open completely.
Improper water valve was installed.
Supply tubing has kinks.
Water filter is clogged or needs to be
changed.
Water valve not opened completely.
Dispenser water
is not cold
Water appears
cloudy
Particles in water Carbon dust from water filter cartridge.
and/or ice cubes.
Concentrations of minerals in water will
form particles when water becomes
frozen and melts.
Refrigerator has been recently installed.
Water supply in holding tank has been
depleted.
Water has settled into water lines
outside holding tank and has warmed to
room temperature.
Air or air bubbles in water.
A minimum pressure of 2/41kpa is recommended for
refrigerators with water filters.
Open saddle valve completely.
See TemperatureControls, pages 7-9. Freezer
temperature should be between -18° to -17° C.
The manufacturer recommends using copper tubing for
installation. Plastic is less durable and can cause
leakage. The manufacturer is not responsible for
property damage due to improper installation or
water connection.
See Connecting the Water Supply page 3. Self-piercing
and 3/Z'saddle valves cause low water pressure and
may clog the line over time. The manufacturer is not
responsible for property damage due to improper
installation or water connection.
Water pressure must be between 241 to 689 kpa to
function properly. A minimum pressure of 241 kpa is
recommended for refrigerators with water filters.
Open saddle valve completely.
See Connecting the Water Supply, page 3. Self-piercing
and 3/Z'saddle valves cause low water pressure and
may clog the line over time. The manufacturer is not
responsible for property damage due to improper
installation or water connection.
Turn off water supply and remove kinks.
If kinks cannot be removed, replace tubing.
Change water filter ([seepage 16].
Open water valve completely and check for leaks.
The minimum flow at dispenser is approximately
295 ml in nine seconds with a new filter in place or
approximately 295 ml in five seconds without a filter.
Allow approximately 12 hours for water in holding tank
to chill.
Discard first glass of water and refill.
This is normal when first using the dispenser and will
disappear with use.
Initial water ejected through cartridge may contain
harmless carbon dust flushed from cartridge.
Particles are safe for consumption.
Will disappear after the first few uses.
Particles are not harmful and naturally occur in water
supplies.
27
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maytag gc2227 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maytag gc2227 in the language / languages: English as an attachment in your email.

The manual is 4,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info