778510
17
Zoom out
Zoom in
Previous page
1/22
Next page
FUEL MIXING
The fuel tank has a maximum capacity of 1 litre. To mix the fuel correctly, use the fuel mixing bottle
to measure the correct amount of oil to petrol.
Warning! Do not mix the fuel in the hole borer fuel tank. Measure the fuel into the fuel mixing bottle
then add the correct proportion of two stroke oil according to the markings on the fuel mixing
bottle, Agitate the container to ensure thorough mixing of the petrol and oil.
Filling the fuel tank
Use a suitable funnel to transfer the fuel mix from the container to the hole borer fuel tank, taking
care not to spill any fuel or over ll the fuel tank.
Please note that for safety reasons this product has been supplied with the fuel system completely
drained of fuel and the engine will require ‘running in’.
When starting for the rst time you may experience some difculty in starting the hole borer. Once
the fuel has fully circulated through the system the hole borer will start. Once started and ‘run in’
future starting will be easier.
STARTING THE ENGINE (PICS.3 TO 6)
Gently agitate the fuel mix by gently rocking the hole borer backwards and forwards a few times.
This will ensure that the 2-stroke oil has not settled out from the petrol.
Set the choke lever to the ‘On’ position (Pics.3).
If the carburetor requires ‘priming’, pump the clear rubber priming button (Pics.4) until fuel appears
in the clear rubber priming button.
If the carburetor requires priming, pump the clear rubber priming button (Pics.4) until fuel appears in the
clear rubber priming button.
Make sure that the STOP/RUN switch is in the RUN position (Pics.5) (5.1).
Hold down the hole borer firmly with one hand. With the other hand grip the recoil starter cord
handle (Pic.6) and pull slowly until resistance is felt indicating that the recoil starter is engaged.
When resistance is felt pull the cord sharply.
Continue this procedure until the engine starts.
When the engine has been successfully started and is running smoothly return the choke lever to the OFF
position.
Press in the safety switch lever (Pic.5)(5.2) then squeeze the throttle lever (Pic.5)(5.3), the auger bit will
begin to rotate. To adjust the boring speed rotate the speed adjuster (Pic.5)(5.4) until the desired setting is
achieved.
To stop the auger bit from rotating. briefly squeeze then release the throttle lever.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxxtools 20570 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxxtools 20570 in the language / languages: English, Dutch as an attachment in your email.

The manual is 2.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info