769817
15
Zoom out
Zoom in
Previous page
1/32
Next page
Decorative Fireplace EN
15
6. Release the plug connection and
connect a new ultrasonic atomiser to
the plug connector of the main unit
(Picture E).
If the cable drops into the hous-
ing, remove the water tank and
thread the cable back through the
corresponding opening.
7. Stow the plug connection in the hous-
ing and fi x the cable in place by fi rmly
pressing the plug in the housing.
8. Insert the ultrasonic atomiser into the
mount in the water tank and its cable
into the cable guide. When you do
this, make sure that the ultrasonic
atomiser is fully inserted and is fi tted
straight.
9. Insert the splash guard into the water
tank and place the cover on the main
unit.
TROUBLESHOOTING
If the device does not work properly,
check whether you are able to rectify the
problem yourself. If the problem cannot
be solved with the steps below, contact
the customer service department.
Do not attempt to repair an
electrical device yourself!
The device does not work.
The mains plug is not inserted in the plug
socket correctly.
Correct the fit of the mains plug.
The plug socket is defective.
Try another plug socket.
The toggle switch (6) is in theO position.
Move the toggle switch into the I
position.
The water tank (7) is empty. In this case,
the device cannot be switched on.
Fill the water tank.
An ultrasonic atomiser (1) does not
work.
The diaphragm is dirty.
Clean the diaphragm.
The ultrasonic atomiser (1) is not plugged
correctly on the connector of the main
unit (5).
Check the plug connection and
correct it if necessary.
The fl ames are small. / The fl ame
pattern does not develop.
The device has only just been switched on.
The device requires a little time to
produce a realistic flame pattern. The
flame pattern will develop as the de-
vice is used and become increasingly
more vivid.
The diaphragm of the ultrasonic atomis-
ers(1) is dirty.
Clean the diaphragms.
The ultrasonic atomiser(1) is tilted in the
mount.
Correct the fit of the ultrasonic atom-
iser. The diaphragm must be pointing
straight up and must not be tilted.
The cable of the ultrasonic atomiser (1) is
protruding over the diaphragm.
Correct the fit of the cable. The
area above the diaphragm needs to
remain clear.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxxmee BG-E-0220 - 08827 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxxmee BG-E-0220 - 08827 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Maxxmee BG-E-0220 - 08827

Maxxmee BG-E-0220 - 08827 Additional guide - English, German, Dutch, French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info