629542

Maxview MXL002 OMNISAT DOME Manual

6
Zoom out
Zoom in
Previous page
1/22
Next page
Remove the Omnisat Dome from the packaging and check it visually.
PACK CONTENTS
Satellite system
Satellite Receiver
2 x ‘F’ connectors
1 x Boot
INSTALLATION ON THE VEHICLE
1. Position the Omnisat Dome on top of the vehicle carefully, in your chosen location.
The ‘F’ connector and blue pressure balancing pipe should be directed to the rear of the vehicle.
Caution: Installation which is made without using spacers on irregular surfaces may cause distortion
of the system. This may effect the operation of the equipment and cause permanent damage.
If the surface of the vehicle slopes, the left and right sided plates of the antenna will not
lie flat on the surface. In such cases, use spacers (not included) to fill the gaps.
Receiver and power cable
Remote control handset x 2 AAA batteries
Screw and washer pack (x 8 of each)
Cable entry cover
8m Coaxial cable
‘F’ to ‘F’ coaxial lead
Infra Red extender
Receiver brackets
✘
✘
6 39
While the system is operating a faint motor sound can be heard, this is normal.
Satellite reception is only possible when the dome is positioned so that it has direct line of sight in the direction
of the desired satellite and there are no obstructions blocking the view, e.g. trees, buildings.
The signal receiving performance of the system may decrease with heavy rainfall or snowfall. The same result
may occur if the antenna is covered with snow. In such a case, gently remove the snow from the antenna cover.
Dirt on the dome may decrease the signal receiving performance over a period of time. To prevent decrease of
performance gently clean the antenna cover periodically.
Do not use abrasive cleaners as they may damage the product’s surfaces.
Do not use solvent based cleaning agents on plastic parts.
To turn off the system press power button on the front panel of the receiver or “STANDBY” button on the
remote control handset. The LED on the front panel will go out and the system switches off.
USAGE
Press the “ ” button on the front panel of the receiver or the “STANDBY” button on the remote control handset
to operate the system. The LED on the front panel will come on and the system will start to operate.
When the system is operating, the antenna starts to search for the selected satellite. The search is completed
in about 20 seconds. After the satellite is found, the system defines the most suitable antenna position by fine-
tuning and then stops. After the satellite has been found the receiver channels can be watched.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxview MXL002 OMNISAT DOME at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxview MXL002 OMNISAT DOME in the language / languages: English as an attachment in your email.

The manual is 7,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info