Manual Maxview MXL001 (page 5 of 10) (English, German, Dutch, French)

629541

Zoom out

Zoom in

1/10

■ PRODUCT ASSEMBLY DIAGRAM

EXPLOSIONSZEICHNUNG

ONDERDELENSCHEMA

SCHEMA D’ASSEMBLAGE DES COMPOSANTS

Probleem: De kantel- en parkeerstops zijn moeilijk te vinden op de draaihendel.

Oplossing: De stops zitten intern en het zijn zachte stops, dus zodra u wat weerstand voelt, is dit de

parkeer- of kantelgrensstop. F

orceer de hendel niet, dit beschadig

t het toestel.

Probleem: Er is geen televisiebeeld te ontvangen

Oplossing: Controleer of het zicht in de richting van het zuiden vrij is. Er mogen geen obstakels voorkomen in de richting van de satelliet zoals:

bomen, huizen etc. Let u erop u dat bij de semitronicantenne te maken heeft met een offset-antenne. Dat betekent dat als de antenne

loodrecht staat (90 gr

aden), en deze in een hoek van 23 gr

aden naar de satelliet gericht staat. Controleer of de televisie en de

Sat-receiver op elkaar zijn afgestemd. Bij gebruik van enn Scartkabel moet de televisie op AV ingeschakeld zijn.

Problème: Les butées d’élévation et de repos semblemt difficiles à trouver sur la poignée.

Solution: Les butées sont internes et douces, alors dès que vous ressentez une certaine résistance, vous avez atteint la butée de repos ou

d’élévation. Ne forcez pas la poignée pour ne pas endommager l’unité.

Problème: Aucune réception d’image

Solution: S’assurer qu’il n’y a aucun obstacle (arbes, maisons etc) entre l’antenne et le sud. Ne pas oublier qu’il s’agit d’une antenne

semitronic: c’est-à-dire que si l’antenne est en position verticale (90˚), cela signifie qu’elle forme un angle de 23˚ avec le satellite.

Vérifier que le téléviseur est réglé sur le démodulateur. En cas de câble scart, le téléviseur doit être sur AV.

Problem: Die Elevations - und Parkpositionen sind beim Drehen der Kurbel schwer zu erkennen.

Lösung: Die Anschläge werden durch einen inneren Mechanismus erzeugt - sobald Sie einen Widerstand fühlen,

sind Sie am Anschlag der oberen bzw. unteren Elevationsgrenze angelangt. Wenden Sie keine Gewalt an

um die Kurbel weiter zu drehen.

Problem: Kein F

ernsehbild zu empfangen

Lösung: Vergewissern Sie sich das die Sicht Richtung Süden frei ist. Es dürfen kein Hindernisse wie Bäume, Häuser usw. die Sicht zum

Satelliten behindern. Achten Sie darauf das es sich bei der Winder um eine Offset-Antenne senkrecht handelt d.h. wenn die

Antenne steht (90˚) dann schaut Sie im Winkel von 23˚ zum Satellit. Stellen Sie sicher das der Fernseher und Sat-Receiver

aufeinander abgestimmit sind. Bei Verwendung eines Scart-Kabel muß beim T

V-

Ger

ät auf AV geschaltet werden.

Problem: The elevation and park stops seem hard to find on turning handle.

Solution: The stops are internal and are soft stops, so as soon as you feel some resistance this will

e the park or elevation limit stop. Do not force the handle, as this will cause damage to the unit.

roblem:

o signal being received

Solution: First check that the dish is pointing in a southerly direction with a direct line of sight with the satellite. Ensure that there are no

obstacles such as trees or houses obstructing the line of sight between the dish and the satellite. Please bear in mind that the

Manual Mast Satellite System has an offset dish. When the dish is in the vertical (90˚) position, the reception beam is at an

levation of 23˚ (it’s offset value). The elevation angle shown on the Zonemap is only correct when the vehicle is level, any angle

from the horizontal will need to be taken into account. Check that the TV and satellite receiver is compatible with each other.

f using a scart lead, the TV must be switched to the AV channel.

■ PROBLEMLÖSUNGEN

■ STORINGZOEKEN

■ DEPISTAGE DE PANNES

■ TROUBLESHOOTING

✔

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Maxview MXL001 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Maxview MXL001 Manual

Product: