171515

Maxdata platinum 500 i Manual

12
Zoom out
Zoom in
Previous page
1/35
Next page
12 13MAXDATA Server PLATINUM 500 I M7Server System Features
12 13MAXDATA Server PLATINUM 500 I M7Server System Features
Table 3. LEDs
Designation Definition
5 V Standby LED The LED is labeled “5VSB_LED”. It is illuminated when AC power is applied to
the platform and 5 volt standby voltage is supplied to the server board.
System ID LED. The blue identification LED can be turned on and off with appropriate system
management software (e.g. Active Management Console).
It helps identify a system for servicing when multiple servers are present.
System Status LED The system status LED is a bi-color LED. It can show the following states:
• Green, solid-on: Normal operation
• Green, blinking: Degraded operation, e.g. processor error, DIMM failure
• Amber, blinking: Non-critical error, e.g. voltage, temperature out of range
• Amber, solid-on: Critical error, e.g. fan failure
DIMM Fault LEDs The DIMM fault LED identifies faults in the assigned memory module
Post Code
Diagnostic LEDs
Display BIOS-POST codes during system startup
SSI Front Panel Connector
The server board provides a 24-pin SSI front panel connector. The following figure shows the pin-out
for this connector.
Figure 6. SSI Front Panel Connector
A. Power LED D. Reset Button
B. HDD LED E. NIC1 LED
C. Power Button F. NIC2 LED
RAID Support
The server board includes an integrated SATA controller that supports transfer rates of both 1.5 and
3.0 Gbps. The options for hard drive configuration are located in the BIOS Setup under “Advanced”
> “Mass Storage Controller Configuration”.
The option “On-board SATA Controller” is enabled as default and allows the following additional
“SATA Mode” options:
• “Enhanced” – supports up to six SATA devices in Native IDE mode.
• “Compatibility” – supports up to four SATA ports [0/1/2/3] in Legacy IDE mode and two SATA
ports [4/5] in Native IDE mode.
• “AHCI” – supports all SATA ports in Advanced Host Controller Interface mode.
• “SW RAID” – switches on Intel
®
Embedded Server RAID Technology II mode with support for
RAID 0, 1 and 10.
A
B
C
D
E
F
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata platinum 500 i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata platinum 500 i in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info