169742

Maxdata platinum 220 select Manual

17
Zoom out
Zoom in
Previous page
1/31
Next page
16 Server Description
17MAXDATA PLATINUM 220 Server
Network Interface Controller (NIC)
The server board S875WP1-E supports two Network Interface Controllers (NICs), one that runs at
10/100 Mb and is Based on the Intel
®
82562ET NIC and the other that runs at one gigabit and is
Based on the Intel
®
82547EI NIC. When looking at the rear of the chassis, the gigabit NIC is at the
left (closest to the video port) and the 10/100 Mb NIC is at the right. You can disable either or both
NICs through BIOS Setup.
The 82562ET is controlled by the ICH5-R and supports the following features:
• Integrated IEEE 802.3 10Base-T and 100Base-TX compatible PHY.
• IEEE 802.3u auto-negotiation support.
• Full duplex support at both 10 Mbps and 100 Mbps operation.
• Low power +3.3V device with reduced power in unplugged mode and automatic detection
of unplugged mode.
• 3-port LED support.
The 82547EI is controlled by the CSA interface off of the MCH. It supports the following features:
• Basic 10/100/1000 Ethernet LAN connectivity.
• Integrated Gigabit Ethernet Media Access Control (MAC) and physical layer (PHY).
• IEEE 802.3 10Base-T/100Base-TX/1000Base-T compliant physical layer interface.
• IEEE 802.3ab auto-negotiation support.
• Low power (less than 350mW in active transmit mode).
• Reduced power in “unplugged mode” (less than 50mW).
• Automatic detection of “unplugged mode”.
• Communication Streaming Architecture (CSA) port provides higher throughput and lower
latencies resulting in up to 30% higher bus throughput (up to wirespeed).
• Full device driver compatibility.
• Programmable transit threshold.
• Configuration EEPROM that contains the MAC address.
• Teaming and Fail over support.
NIC Connector and Status LEDs
Two LEDs are built into each RJ-45 LAN connector. For the 82562ET NIC, the yellow LED indicates a
link to the LAN and the green LED indicates the connection speed. Table 5 describes the LED states
when the board is powered up and the 82562ET 10/100 Ethernet LAN subsystem is operating.
Table 5. 10/100 Ethernet LAN Connector LEDs
LED Color LED State Indicates
Green
(left LED)
Off
10 MBit/sec data rate is selected.
On
100 MBit/sec data rate is selected.
Yellow
(right LED)
Off LAN link is not established.
On (steady state) LAN link is established.
On (brighter and
pulsing)
The computer is communicating with another computer
on the LAN.
Table 6 describes the LED states when the board is powered up and the 82547EI 10/100/1000 Gigabit
Ethernet LAN subsystem is operating.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata platinum 220 select at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata platinum 220 select in the language / languages: English as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info