169742

Maxdata platinum 220 select Manual

14
Zoom out
Zoom in
Previous page
1/31
Next page
14 Server Description
15MAXDATA PLATINUM 220 Server
Parallel Port
The 25-pin D-Sub parallel port connector is located on the back panel. In the BIOS Setup program,
the parallel port can be set to the following modes:
• Output only (PC AT-compatible mode)
• Bi-directional (PS/2 compatible)
• EPP
• ECP
Floppy Drive Controller
The I/O controller supports one diskette drive that is compatible with the 82077 diskette drive controller
and supports both PC-AT and PS/2 modes.
Keyboard and Mouse Connectors
PS/2 keyboard and mouse connectors are located on the back panel. The +5V lines to these connectors
are protected with a PolySwitch circuit that, like a self-healing fuse, reestablishes the connection after
an overcurrent condition is removed.
NOTE
The keyboard is supported in the bottom PS/2 connector and the mouse is supported in the top PS/2
connector. Power to the computer should be turned off before a keyboard or mouse is connected
or disconnected.
The keyboard controller contains the AMI keyboard and mouse controller code, provides the keyboard
and mouse control functions, and supports password protection for power-on/reset. A power-on/reset
password can be specified in the BIOS Setup program.
USB
High-Speed USB 2.0 Support
NOTES
Use a shielded cable that meets the requirements for a full-speed USB device. Computer systems
that have an unshielded cable attached to a USB port might not meet FCC Class B requirements,
even if no device or a low-speed USB device is attached to the cable.
USB devices are limited to USB 1.1 transfer rates prior to operating system and driver initialization.
The server board supports up to six USB 2.0 ports via the ICH5. Four ports are routed to the back panel.
One header, supporting up to two ports, is routed to the front panel. USB 2.0 ports are backward
compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates. Disabling High-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may
be required to accommodate operating systems that do not support USB 2.0.
Legacy USB Support
Legacy USB support allows USB devices such as keyboard, mice, and hubs to be used even when
the operating system’s USB drivers are not available. Legacy USB support is used to access the
BIOS Setup program, and to install an operating system that supports USB. By default, Legacy USB
support is set to Enabled.
Four of the USB ports are implemented with stacked back panel connectors; the other two are
accessible via the front panel USB header. The S875WP1-E server board fully supports UHCI and
uses UHCI-compatible software drivers.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata platinum 220 select at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata platinum 220 select in the language / languages: English as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info