545558
110
Zoom out
Zoom in
Previous page
1/133
Next page
SFX SERIES USER’S GUIDE
Rev 2.2 108
Important EMI & Safety Certification Information
Read these safety and operating instructions before operating your SFX series satellite receiver. Follow instructions
and heed all warnings on your unit and in this manual.
CAUTION: Equipment must be installed by a qualified service person and earth connection is
essential before connecting supply. Connect your power supply to a grounded AC outlet only.
Receiver Installation
Operate from a power source indicated on your receiver or in this manual.
The AC inlet is the main power disconnect. The socket outlet shall be near the equipment and shall be easily
accessible. The power requirements for this equipment are quite flexible with an acceptable power range of 100
to 240 VAC at 50 or 60 Hz. The fuse is part of the power supply. Replacement can only be accomplished by a
qualified technician.
Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them.
Be especially careful at plug-ins, convenience receptacles or cord exit points from the equipment. Frayed power
cords or damaged plugs are hazardous. Have them replaced by a qualified service technician. Overloaded wall
outlets and extension cords may cause fire or electrical shock.
Always ensure there is adequate ventilation when installing the equipment. Do not cover or block ventilation
holes. Doing so may damage the unit or cause a fire.
Avoid excessive humidity, sudden temperature changes or temperature extremes. Condensation may form inside
your unit.
To avoid costly damage or injury, place your unit on a solid, stable surface or mount in a rack free from vibrations.
Do not place any heavy objects on top.
Exterior Equipment Installation
Refer to the Figure 3 -1 while reading the instructions below.
Grounding the dish provides protection against static voltage build-up, which may damage equipment.
Grounding also provides some protection against surges induced by nearby lightning strikes. Any coax cable
that may be exposed to lightning or power conductors must have its outer shield grounded. There may be
additional grounding regulations in your area. It is important for you to consult and follow all the codes and
regulations in your area as you install your system.
The best method of grounding the outer shield of a coax cable is to use a ground block. This block is a barrel
connector to which you can install a ground conductor, such as a terminal, or a drilled hole and setscrew.
The terminal is where the outer conductor of the coax cable is attached to the grounding electrode. When
installed, the grounding block passes the LNB signal and DC voltages straight through while grounding the
outer conductor of the coax. One factor determining the ground block location is the location of an
acceptable ground electrode. The grounding conductor (the wire that runs between the ground block and the
110


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Max SFX Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Max SFX Series in the language / languages: English as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info