545558
11
Zoom out
Zoom in
Previous page
1/133
Next page
SFX SERIES USER’S GUIDE
Rev 2.2 9
Connector Description
SYNC/RELAY Port This is a X.21 (DCE compatible) DA-15S (female) connector used as a unidirectional
(output) synchronous data port. The pinouts for this port are as follows:
PIN Acronym Reference
1 SHIELD Ground
2 T (A) Not connected
3 C (A) Not connected
4 R (A) Transmit Data A
5 I (A) Data Valid A
6 S (A) Transmit Clock A
7 Relay NC NC Form C Lock
8 GND Ground
9 T (B) Not connected
10 C (B) Not connected
11 R (B) Transmit Data B
12 I (B) Data Valid B
13 S (B) Transmit Clock B
14 Relay NO NO Form C Lock
15 Relay COM Form C Common
ASI Port (optional) This optional port is available for output of the DVB Transport Stream, compliant with
EN50083-9.
Equipment Installation
The following points and precautions should be considered when planning the installation of your satellite receiver.
The satellite receiver should be placed in a sheltered, but well ventilated location away from sources of water
or high humidity, extreme heat or cold, excessive dust, vibration or Electromagnetic Interference (EMI).
Should any foreign material fall into the satellite receiver (either liquid or solid), unplug the receiver
immediately and have a qualified technician examine the unit prior to further operation.
The satellite receiver should be placed on a stable surface or rack mounted, as applicable.
To install your receiver, you should ensure that you have equipment similar to the following:
A computer platform (or laptop computer), with a program such as HyperTerminal to talk to the terminal
interface. If you wish to use the Web GUI, the minimum platform would consist of a Pentium 500 MHz
computer with an installed Local Area Network (LAN) card and Microsoft
TM
Internet Explorer Version 5.0 or
later.
A spectrum analyzer. Although not essential, this piece of test equipment is highly recommended for
installing any satellite equipment.
Power up procedure
It is good practice to do a quick test to ensure the satellite receiver is operational after shipment. To do this, simply
plug the supplied AC power cord into the rear panel of the unit and into the proper voltage AC outlet. If you now turn
the receiver around so that you are facing the front panel, you should notice the STATUS LED is illuminated. After
waiting a minute, you should notice the LOCK LED is also illuminated. At this point, ignore the colour of any indicators,
as this is just an indication that the receiver has power and is commencing operation. You can now communicate with
the unit using the Terminal Interface or the Web GUI, as described in the next sections.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Max SFX Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Max SFX Series in the language / languages: English as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info