472809

Mavic Wintech E-BOLT Manual

12
Zoom out
Zoom in
Previous page
1/100
Next page
12
ENGLISH
3. FITTING/REMOVING THE COMPUTER
3.1 Slide the computer onto the mount from the front until it
locks into place with an audible click.
3.2 To remove the computer, press the button underneath the
mount and slide
the computer out
towards the front of
the bike.
4. INSTALLING THE SENSOR NUT
4. Installing the Sensor nut
The speed sensor in this computer is integrated into a fixing
nut compatible with all quick-
releases on the market.
To install it, unscrew the fixing
nut on your quick-release.
Insert the quick release from the
left-hand side of your bike and
tighten the electronic fixing nut
from the right-hand side.
Adjust the tightness of the nut
so that the quick-release locking
lever can be sufficiently firmly
pushed into the CLOSE position
(if in doubt, consult your retailer
or the hub manual).
4.1 Road bike.
Once sufficiently tightened,
position the sensor towards the
rear before closing the quick-
release hub.
4.2 Mountain bike.
Once sufficiently tightened,
position the sensor towards the
top before closing the quick-
release hub.
6. INSTALLING THE BATTERIES
Power supply for the computer: 1 CR2032 battery.
Power supply for the speed sensor: 1 CR2032 battery.
Only use this type of battery.
Installing the batteries:
6.1 Remove the battery cover by turning
it a quarter turn anticlockwise, using
a coin.
6.2 Insert the battery into its recess,
keeping the + side uppermost.
6.3 Refit the battery cover and close it by turning
it a quarter turn clockwise.
Do not to use excessive force, or you will
damage the unit.
Check the condition of the seal on the battery
cover each time you change the battery. Replace
the battery cover if the seal is damaged.
Always perform the above operations in a dry
place.
1
2
5.3
6.2
6.1
4
5.1
4.1
5.2
5. INSTALLING THE MAGNET
5.1 Position the magnet on a spoke so that it passes opposite
either of the lever marks and at a maximum distance of
5 mm.
When used on a mountain bike, it might be necessary to use
the adjustment magnets to reduce the distance between the
sensor and the magnet. (5.2).
The magnet must be facing outward from the wheel.
5.3 Must be cut for use on profiled Zicral spokes
4.2
3.1 3.2
8. FUNCTION
8.1 To scroll dis
Screen 1:
• Spot speed
• Number of bi
k
• Pedaling cade
• Trip distance
Changing the c
effect of zeroing
total distance, m
(M or KM), whe
After installatio
batteries
(in sensors or
imperative to
r
described in se
Battery life: 12
7. DESCRIPT
wintech-esbolt bis.indb 12wintech-esbolt bis.indb 12 20/03/07 12:34:1720/03/07 12:34:17
Cyan quadriMagenta quadriJaune quadriNoir quadri
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mavic Wintech E-BOLT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mavic Wintech E-BOLT in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 7,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info