Manual Mastercraft X46 (page 210 of 285) (English)

614265

210

Zoom out

Zoom in

1/285

Care and Maintenance • 2014 MasterCraft Owners Manual Page 6-17

C A R E A N D M A I N T E N A N C E

Step 1: Ensure the engine is OFF and the

enginesafetystartingswitchdis-

connected. Be certain that the

throttle/shift control lever is in

neutral. Locate the battery. Bat-

teriesareplacedinavarietyoflo-

cations, depending on the model.

Check under the observer seat or

behind the rear seat.

Step 2:  Check that the battery post con-

nections are clean and tight. If

not:

• Loosen and remove the negative ter-

minal connection rst. Be careful not

to touch the positive terminal with the

wrench.

• Loosenandremovethepositiveterminal

connection.

• Removethebatteryhold-downsandre-

movethebatteryfromtheboat.

•  Clean corrosion from the battery posts

withabatteryterminalcleaner.

•Cleanthebatterywithawater-and-bak-

ing-soda solution. Use care to avoid al-

lowingthesolutiontoenterthebattery

vents.Rinsethebatterywithfreshwater.

Battery electrolyte fluid is dangerous. It

contains sulfuric acid, which is poison-

ous, corrosive and caustic. If electrolyte

fluid is spilled or placed on any part of the

human body, immediately flush the area

with large amounts of clean water and im-

mediately seek medical attention.

• Useabatteryterminalcleaningbrushto

remove corrosion from the inside of the

battery terminals. Clean the terminals

with a water-and-baking-soda solution

and rinse with fresh water.

• Check the battery box that normally

holdsthebatteryinplacetodetermine

whether there is evidence of battery

uidinsideit.Batteryuidsarecorro-

sive and can cause permanent damage

to the battery box. If uid is evident,

wash out the box with the water-and-

baking-soda solution that is used in

cleaning the terminals. Rinse with

freshwateranddrywithacloth.

• Reconnectthepositiveterminalrst,then

the negative. Tighten the terminals. Coat

bothterminalscompletelywithathincov-

eringofmarinedielectricgrease.Besure

that the rubber boot covers the positive

terminalcompletely.

Note: The boat’s engine is designed to

work with the standard electronics in-

stalled in the boat. Adding other electrical

components or accessories can change the

way the fuel injection controls the engine

or the overall electrical system functions.

Before adding electrical equipment, con-

sult an authorized MasterCraft dealer’s

service department. Otherwise, the engine

may not perform properly.

Add-on equipment may adversely aect

the alternator output or overload the elec-

trical system. Such damage may not be

covered by the warranty.

Ifareplacementbatteryisrequired,be

certain to select a marine battery with at

leastseven-hundred-fty(750)cold-crank-

ing-amps at zero degrees (0

) Fahrenheit.

Before disconnecting the battery, make

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mastercraft X46 in the language / languages: English as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mastercraft X46 Manual

Product: