Manual Mastercraft X35 (page 258 of 285) (English)

614264

258

Zoom out

Zoom in

1/285

MasterCraft Trailers • 2014 MasterCraft Owners Manual Page 7-33

M A S T E R C R A F T T R A I L E R S

master cylinder reservoir by unscrewing

the cap in a counter-clockwise direction.

The brake uid level should be 1/8” be-

low the threads.

• Check for foam or bubbles in the brake

uid. If either is present, drain the uid

from the master cylinder and replace with

ONLY new brake uid of the same type

(DOT 3—preferred—or 4). DO NOT

USE DOT 5 FLUID. (See specic infor-

mation in Recommended Brake Fluid in

this section of this Owner’s Manual.) In

order for brakes to function properly, all

air must be expelled from the brake sys-

tem. If bleeding is necessary, have an au-

thorized MasterCraft dealer perform this

function or follow the manual bleeding of

the brake system instructions as outlined

in this Owner’s Manual. It is imperative

that the system be lled with only ONE

type of brake uid. Different types do not

mix. Follow the instructions on the brake

uid container.

• Check the safety chains and attachment

points for damage or wear. Repair or re-

place as necessary.

• Check the breakaway cable for worn or

frayed cable strands. End ttings should be

checked for damage. Replace as necessary.

• Check for any hydraulic leaks in the

brake system. Be sure all tube ttings

are tight. Periodic checks must be made

on all hoses, brake line tubing and t-

tings to guard against cuts, worn hoses

and loose ttings that may cause leaks

in the trailer brake hydraulic system. Re-

place deteriorated and damaged parts as

necessary.

• Check for chips and nicks in the paint.

Touch up as necessary. Ignoring this will

lead to accelerated wear and deteriora-

tion of the trailer.

• Check the condition of the bunks. If the

coverings show wear, discuss with an

authorized MasterCraft dealer. If the

coverings are not in good condition or if

the bunk sub-frame shows any damage,

this will adversely affect the t of trailer

to boat. This can result in damage to the

boat hull, which is not covered under

warranty.

Storage(forseveralmonths):

• If at all possible, park the boat trailer in

a protected, covered area such as a ga-

rage, carport or similar shelter. Keep all

canvas covers on the boat while stored,

but in higher humidity areas or periods

of weather, it may be necessary to open

a corner of the covered area to allow air

circulation. See the Care and Mainte-

nance section of this Owner’s Manual

for additional information and sugges-

tions regarding storage procedures.

• Have the wheel bearings checked by an

authorized MasterCraft dealer prior to

re-use.

• Loosen the tie-downs and winch strap,

but be sure the boat is still resting prop-

erly on the hull supports (bunks).

• Remove the drain plug and elevate the

trailer tongue slightly (just an inch or

two) to allow water to drain out so the

boat will be dry. Tie the drain plugs from

the boat’s bilge system to something ob-

vious such as the steering wheel so that

they will be easy to remember to re-in-

stall before the next outing.

• A good time to touch up rust spots, nicks

and chips is when the trailer is in storage.

• Replace damaged tie-downs, winch

straps, wiring, etc.

• Maintain proper tire ination.

• Shield tires from UV rays (direct sun-

light).

• Relieve the load on the tires by support-

ing the trailer frame with concrete blocks

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mastercraft X35 in the language / languages: English as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mastercraft X35 Manual

Product: