Manual Mastercraft X35 (page 257 of 285) (English)

614264

257

Zoom out

Zoom in

1/285

Page 7-32 2014 MasterCraft Owners Manual • MasterCraft Trailers

M A S T E R C R A F T T R A I L E R S

• Verify the safety cables are properly at-

tached to the tow vehicle.

• Verify the emergency brake cable is at-

tached properly to the tow vehicle.

• Verify the boat is properly loaded on

the trailer and properly tied down to the

trailer.

• Verify and/or correct tire pressure on

both the tow vehicle and trailer.

• Ensure the lug nuts are properly torqued.

(This must also be done after the rst

25 miles of towing and every 100 miles

thereafter, at a minimum. MasterCraft

recommends checking this more often.

At each fuel or rest stop is not exces-

sive.)

• Verify the wheel jack is retracted, up and

in the locked position prior to towing.

• Verify the tow vehicle has not exceeded

the load capacity prior to towing.

• Check the guide pole bars to ensure they

are tight.

• Check that all items are securely fas-

tened on and in the trailer.

Every three to six months or 250 miles,

whichever occurs rst (in addition to

above):

• Grease the trailer jack.

• Oil the trailer jack handle in accordance

with the manufacturer’s recommenda-

tions.

• Examine the entire trailer for any abnor-

malities or damage.

• Examine the trailer bunks for any signs

of abnormal wear.

• Lubricate all the rollers on the trailer

with a light coat of oil.

Annuallyorevery2,000miles,whichever

occursrst(inadditiontotheabove):

• To assure the bearings are in good work-

ing order, check the bearing adjustment

at least once a year by following this

procedure: Jack up one side of the trailer.

(Becertaintousejackstandsandcheck

the trailer wheels to keep the trailer

from moving during the inspection.)

Grip the edge of the tire and see if it can

be rocked or moved. If the outer edge of

the tire moves more than 1/8” at all, the

bearings may need to be readjusted.

• Inspect the tow hitch for corrosion or

damage. Repair or replace components

as necessary.

• Check for wear on the hitch ball. If the

ball is worn, it is UNSAFE and must be

replaced.

• Check the coupler mechanism for

smooth operation. If the button is hard to

push or the latch handle does not spring

open after being disengaged, lubricate

the points on the coupler latch mecha-

nism.

• Check the actuator for excessive wear.

If the outer member is rubbing against

the inner, wear marks will show on top

of the coupler just forward of the outer

member. Contact an authorized Master-

Craft dealer for replacement parts.

• Check the actuator travel. Excessive ac-

tuator travel (over one inch) when the

brakes are applied indicates air in the

brake lines.

• Check the brake uid in the master cyl-

inder reservoir. On the UFP actuator, to

gain access to the reservoir, remove the

cap on top of the actuator. Clean the area

around the master cylinder plug. Use

a screwdriver to carefully pry off the

plug. Make sure the rubber seal around

the opening is in good condition. Clean

brake uid off the level indicator on the

plug. Re-install and remove the plug.

Brake uid should just touch the end of

the level indicator. On the Tie Down En-

gineering actuator, remove the cap to the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mastercraft X35 in the language / languages: English as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mastercraft X35 Manual

Product: