705279
3
Zoom out
Zoom in
Previous page
1/7
Next page
ENGLISH
PLEASE READ THIS MANUAL CAREFULLY
BEFORE PLUGGING IN.
FOLLOW ALL INSTRUCTIONS AND HEED ALL WARNINGS.
KEEP THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modications not expressly approved by the party
responsible for compliance could void the users authority to operate the equipment.
This device complies with CAN ICES-3(B)/NMB-3(B)
COMPLIANCE STATEMENT
WARNING:
Before going any further, make sure that
your amplier is compatible with your
mains electricity supply. If you have any
doubt, please seek help from a qualied
technician – your Marshall dealer can
help you in this respect.
MAINS INPUT & FUSE:
The specic mains input voltage
rating that your amplier has been
manufactured for is indicated on the
rear panel of the amplier. Your amplier
is provided with a detachable mains
(power) lead, which should be connected
to the MAINS INPUT socket on the rear
panel of the amplier (Rear Panel Function
#16). The correct value and type of
mains fuse is specied on the rear panel
of the amplier.
NEVER attempt to bypass the fuse or t
one of the incorrect value or type.
TRANSPORTING YOUR EQUIPMENT:
Please ensure that your amplier is
switched off, unplugged from the mains
electricity supply and all removable
cables have been disconnected from
your equipment before attempting to
move it.
IMPORTANT SET UP INFORMATION:
1. When using the DSL20HR, or the
DSL20CR with an extension speaker
cabinet(s), make sure that the
speaker cabinet(s) is connected to
the correct impedance loudspeaker
jack socket(s) on the rear panel of the
amplier. See the LOUDSPEAKERS
guide in this manual for specic
information regarding impedance
matching (Rear Panel Function #22).
WARNING:
Failure to do the above may damage
your amplier. When connecting a
speaker cabinet make sure that you
use a proper speaker cable. Never use a
screened (shielded) guitar cable for this
purpose.
2. Ensure that the POWER switch is
set to the OFF position (Front Panel
Function #15).
3. Ensure the OUTPUT switch is in the
STANDBY position
(Front Panel Function #14).
4. Connect the supplied mains (power)
lead into the MAINS INPUT (Rear
Panel Function #16) rst and then
into an electricity outlet.
5. Ensure that the volume controls on
the front panel are set to zero (Front
Panel Functions #3 & #6).
6. Plug your guitar into the INPUT jack
socket (Front Panel Function #1).
7. Switch the amplier ON using the
POWER switch, wait for a few
minutes and then switch the
OUTPUT switch to either the LOW
or HIGH position.
8. Turn the front panel POWER switch
on and wait for a few minutes
before going to point 9.
9. Turn the selected channel volume
up to your preferred level and your
amplier is ready to play.
WARNING! IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall DSL20HR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall DSL20HR in the language / languages: English as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info