163890

Marquant mcr-1290 Manual

11
Zoom out
Zoom in
Previous page
1/34
Next page
1717
1010
3. Radio Operation
1. BAND BUTTON
In RADIO mode, press the BAND button on the remote controller or on the front panel to
select your desired radio band of FM1, FM2, FM3, MW1 and MW2, and the word means which
band is selected will be displayed on the small monitor of the front panel.
2. TUNE/SEEK UP/DOWN BUTTONS
In RADIO mode:
1) Long press the UP/DN button on the front panel or the >>|/ |<< button on the remote controller
to automatically search up/down for a available station from the current frequency.
2) Briefly press the UP/DN button on the front panel or the >>| / |<< button on the remote controller
to manually search up or down with step by step for your desired station from the current
frequency.
3. APS BUTTON
In RADIO mode:
1) When long pressing the APS button, the radio searches from the lowest frequency and checks
the signal strength level until 1 cycle search is finished. And then the 6 strongest stations are
preset to the corresponding preset number memory bank. The AS operation is implemented in
the each bank of the selected band. When the AS operation is finished, it will resume broad-
casting on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)
2) When briefly pressing the APS button on the front panel or the remote controller, the radio
searches for each preset station from the M1. When the field strength level is more than the
threshold level of the stop level, the radio is holding at that preset number for few seconds with
releasing mute, and then searches again. After finishing a circle of searching, it will stop
searching on the M1.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.
4. PRESET STATION [ 1-6 ] BUTTONS
In RADIO mode:
1) To memorize the current frequency on the current band, long press any one of the six preset
buttons (1-6) , or press the ^/v button to select a memory bank and then long press the OK button.
2) To recall the preset memory on the current band, press one of the preset buttons [1-6] or press
the ^ / v button and then press the OK button to confirm.
5. STEREO/MONO BUTTON
Press the ST button on the remote controller to select the STEREO or MONO sound mode for
FM band.
6. LOC BUTTON
1) In FM mode, when the signal of the distance radio station are very weak and the receiving
effect is bad during tuning, check whether there is the word LOC on LCD. If there is the word
LOC on LCD, press this button to turn off the LOC function, then tune again for the distance
radio station;
2) In FM mode, when the signal of the local radio station are too strong to lead that the interference
to the receiving effect during tuning, press this button to turn on the LOC function to display the
word LOC on LCD, then tune again for the local radio station.
ZOOM 2,ZOOM 3,ZOOM 4,ZOOM 1/2,ZOOM 1/3,ZOOM 1/4,ZOOM OFF.
Press one of the ^/v/>/< buttons to select the area you want to enlarge.
5.10 Change the Caption Language
In the state of DVD disc playing, press the SUBTITLE button repeatedly to
select the language of the caption or turn off the caption.(depend on the
disc used.)
In the state of VCD/MP3/WMA/CD disc playing, the button is not available.
5.11 Change the Audio Language
1. In the state of DVD disc playing, press the AUDIO button repeatedly
on the IR remote controller to select the desired language type.
(depend on the disc used)
2. In the state of VCD/MP3/WMA/CD disc playing, press the AUDIO button
repeatedly to select the sound mode of the MONO L, MONO R, and Stereo,
no language function.
5.12 Change the Video Signal System
During playback of DVD/VCD disc, press the P/N button on the front panel
repeatedly to change the VIDEO SIGNAL SYSTEM mode as follows:
--> PAL--> AUTO --> NTSC -->
5.13 Look over the Playback Status
1. In the state of DVD disc playing, press the OSD button repeatedly on the
remote controller to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing title, the
serial number of the playing chapter, the elapsed time of the playing chapter,
the remained time of the playing chapter, the elapsed time of the playing title,
the remained time of the playing title, etc.
2. In the state of VCD/MP3/WMA/CD disc playing, press the OSD button
repeatedly on the remote controller to turn on/off the playback status. When
it is on, it will display the information such as: the serial number of the playing
track, the elapsted time of the playing track, the remained time of the playing
track, the elapsted time of the disc, the remained time of the disc.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marquant mcr-1290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marquant mcr-1290 in the language / languages: Dutch, French as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info