489106

Marmitek TV Anywhere Manual

13
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISH
13TV Anywhere™
1. Make sure your device is switched on.
2. Press and hold SETUP [7] until the LED indicator stays lit. Release SETUP.
3. Press the mode button [3] that matches the device you want to control (for example TV).
4. Press Prog+ [5] repeatedly until the channel changes. If you step past the correct code, use
Prog- [5] to go back to the right code.
5. When the device you want to control reacts, press ENT [11] to confirm the code.
! If your equipment does not have Prog+, you can use PLAY (VCR or DVD) [19] or
POWER [1]. The search starts after the last registered code. Note: if certain functions
of your equipment cannot be controlled, you will have to find a different code for
your brand.
5.6 Identifying codes found
If the batteries have been outside the remote control for a longer period, the programmed
codes may be erased from the memory. It is a good idea to write down the codes, so you can
reprogram the remote control quickly. If you don’t know the code (for example because you
found the code by autosearch), you can identify it as follows:
1. Press and hold SETUP [7] until the LED indicator [2] stays lit. Release SETUP.
2. Press the mode button [3] for the device you want to identify (VCR, DVD, ASAT or DSAT).
The LED will flash once.
3. Press SETUP again. The LED will flash once. To identify the first digit, press each number
button from 0-9 [9] until the LED flashes. The number you pressed, is the first digit of the
code.
5. Press each number key from 0-9 as above to find the second digit.
6. Press each number key from 0-9 as above to find the third digit.
7. Press all digit keys again to locate the fourth digit. As soon as the fourth digit is located,
the LED goes off.
5.7 Configure volume control for various devices
The remote control is preset so that the Volume and Mute keys operate the device which is
programmed by the device keys [3]. If the programmed device does not have a volume/ mute
function then the TV volume will be controlled without having to switch to the TV function.
You can also adjust this set up manually and assign the volume control of the device in
question to the TV, for example, so you adjust the TV volume but not that of, for example,
the set top box, and all this without having to switch to the TV function.
Note, if you perform the procedure below for devices that do not have a volume/ mute
function then the Volume and Mute keys will not work. It is then necessary to switch to the
TV function in order to adjust the volume.
Configuration of one general volume control for all devices operated by the remote
control, e.g. TV:
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off.
3. Briefly press the desired key (3) e.g. TV, the LED flashes and stays on.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek TV Anywhere at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek TV Anywhere in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info