494275

Marmitek SM10 Manual

6
Zoom out
Zoom in
Previous page
1/44
Next page
6 © MARMITEK
APPLICATIONS
The SM10 can be used, for instance, to connect your present (non X-10 compatible) alarm
system to Marmitek X-10 modules:
- A magnetic switch can be connected to the SM10, which can be used to turn lights on and
off when opening or closing doors and windows.
- The SM10 can be connected to the switch contacts of a light sensor or motion sensor or an
(amplified) microphone or humidity sensor in order to activate X-10 modules.
- The door switch of your garage door can be connected to the SM10 to automatically switch
on the lights when the door opens, etc......
INSTALLATION
After a signal has been given at the input, the Marmitek SM10 will send commands via the
mains to the Marmitek X-10 modules. This will switch lights and equipment on and off. This
takes place according to Marmitek X-10 protocol. Because the existing mains system is used,
no additional wiring will be necessary. Individual groups can be controlled by using rotary
switches (so-called HouseCode and UnitCode).
1. Use a small screwdriver to select the HouseCode (A-P) at the system address and the
UnitCode (1-16) at the module number to select the modules you would like to use in
combination with the Mode switch.
2. Connect the switch or sensor to the screw terminals (18 V max. ).
3. Plug the SM10 in a wall outlet.
4. Set the selector switches to the desired positions:
Selector switch Input A – B:
A. The SM10 will be triggered by a voltage (6 – 18 VAC or DC) or an amplified audio signal
(such as a microphone).
B. The SM10 will be triggered by a contact closure of a switch or a relay (such as the alarm
panel).
Selector switch Mode 1 – 2 – 3:
1. The SM10 will turn ON all Lamp Modules set to its House Code and will also turn ON any other
Modules set to its Unit Code (ALL LIGHTS ON). All Lamp Modules are left in the ON state when
the trigger is de-activated but the module set to the same Unit Code will turn OFF.
2. The SM10 will FLASH all lights connected to Lamp Modules (ALL LIGHTS ON / ALL UNITS OFF).
All Lamp Modules will be left in the ON state when the trigger is de-activated but Appliance
Modules set to the same House Code as the SM10 will turn OFF (ALL LIGHTS ON).
3. If a trigger signal is presented to the terminal of the SM10; an “ON” command is send to
the pre-set address. When the trigger signal is switched off again; an “OFF” command will
be sent.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SM10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SM10 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info