494275
5
Zoom out
Zoom in
Previous page
1/44
Next page
enGliSH
5SM10™
Known devices which can cause attenuation are:
PC Monitors
PCs with heavy internal power supplies
Old Televisions
Copiers
Fluorescent Lights
Gas Discharge Lamps (Energy Saving Lamps)
3. Some (old) devices are able to disturb the signal by transmitting noise on the power line.
Because the Marmitek X-10 signals are transmitted on 120 kHz, only noise on or near this
frequency will have influence on the range. When you use a FM10 Filter to connect this device
to the power line, the noise will be filtered.
4. The Marmitek X-10 protocol has several mechanism to avoid modules to be switched on
or off by other sources than your Marmitek X-10 Controllers. However, it is possible that the
Marmitek X-10 signals are disturbed by e.g. baby phones which are in TALK mode (continuous
transmission). When these kind of signals are present on the power line it is possible that the
Marmitek X-10 signals will not come through.
5. The mains do not stop at the front door of your home. Everything that is attached to mains
nearby your home can have influence on Marmitek X-10 signals (e.g. heavy machinery). If you
think that your system is influenced by devices out of your house, it is advisable to install FD10
Phase Coupler/Filter on each phase entering the house. These filters will block signals coming
into or going out of your house, but will also match the impedance for the mains. Hereby make
your house Marmitek X-10 compatible for these units. The FD10’s will not only filter but will
also couple the phases (please see 1).
inSTrUCTiOnS FOr USe
INTRODUCTION
Congratulations on purchasing the SM10! This is a universal X-10 sender for controlling
appliances and lights, that are plugged into the Marmitek X-10 modules, through the existing
house wiring. Automatically switches all lights (on or flashing) in case of alarm, without running
any extra wires. Switch appliances and lights from every location in your home without extra
cables. You can use almost every signal as a “triggerfor the SM10: contact closure (relays,
switch of alarm keypad), but also any voltage between 6 and 18 V (e.g. doorbell transformer
or amplified audio signal).
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SM10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SM10 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info