494336
4
Zoom out
Zoom in
Previous page
1/5
Next page
19
Note
If no setting command is received within 60 seconds the module
will automatically exit programming mode.
Cancelling programming mode
Briefly press the program button
once; the red LED is now off,
or wait 60 seconds so
that programming mode
is cancelled automatically.
!
Figure 1. To activate and cancel programming mode, insert a screwdriver through the
opening (A) in the rear of the box.
A
20
Programming (continued)
Programming the options
The table below shows the standard settings and options.
The SAX35 is set to "Standard".
Proceed as follows to access the options:
Put the module into programming mode.
Send the desired command in "Setup Command" twice,
via a program and measurement interface (PMIX35) or a
Marmitek X-10 Control Box.
The program LED confirms the "Setup Command" by flashing a
specific number of times.
Cancel programming mode.
Must always be programmed
Standard Optional Setup Number
Command flashing
Send address A1 A1 … P16 Desired address 1
Receive address A3 A1 … P16 Desired address 2
Note: If the receive address is programmed lower than the send
address, one free address should be left between the two
addresses. The programmed send address and programmed
receive address must therefore always differ by at least
2 addresses. Example: if the send address is C7, the receive
address cannot be programmed as C6, C7 or C8.
21
Optional settings for the output:
Standard Optional Setup Number
Command flashing
No All Lights On All Lights On All Lights On 6
No All Lights Off All Lights Off All Lights Off 10
No All Units Off All Units Off All Units Off 8
Note
When in programming mode, always enter the address first
and then the other settings.
When a new address is programmed the optional commands
are lost (reset).
!
22
Programming (continued)
Example where the send address is programmed on D3 and the
receive address on D6
Event Result
Input 1 is connected to supply SAX35 sends D3 Don
Input 1 is disconnected SAX35 sends D3 Doff
Input 2 is connected to supply SAX35 sends D4 Don
Input 2 is disconnected SAX35 sends D4 Doff
SAX35 receives D6 Don Relay contact closes
SAX35 receives D6 Doff Relay contact opens
23
Input 1
Input 1
Input 2
Input 2
Uitgang 2
Relais
output
3k2
3k2
R1
R5
X4
D2
D1
X2
+
+
SAX15
Figure 2. Internal diagram of galvanically separated section.
24
Connection example
Figure 3 shows an application in which an input on the SAX35 is
activated by a bell transformer switch. In this way, pressure on
the doorbell button is converted into a Marmitek X-10
command. When doorbell switch S1 is closed, the SAX35 sends
the programmed send address plus an ON command. When S1
is opened, the SAX35 sends the programmed send address plus
an OFF command.
Lamp L1 is switched by the relay output. When the SAX35
receives the programmed receive address plus an ON
command, L1 will switch on. When the SAX35 receives the
programmed receive address plus an OFF command, L1 will
switch off.
230 V~
+
Input 1
L1
Transformer
Relais
output
Figure 3.
Connection
applications
example.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SAX35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SAX35 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info