494336
3
Zoom out
Zoom in
Previous page
1/5
Next page
13
Marmitek is niet verantwoordelijk voor het disfunctioneren
van het Marmitek X-10 -systeem als gevolg van in het
gebouw aanwezige apparatuur met emissiewaardes boven de
maximale toegestane niveaus zoals die gelden in residentiële,
commerciële en lichtindustriële omgevingen en zijn
vastgelegd in de EN 61000-6-3.
Toepassing Geldende Europese norm Marmitek X-10 -huis
automatisering*
Immuniteit van Emissie van Immuniteit- en
de apparatuur de apparatuur emissienorm
Residentieel 61000-6-1 61000-6-3 Compatibel/
Commercieel voldoet
Licht-industrieel
* Voorwaarde daarbij is dat het gehele Marmitek X-10 -systeem wordt
geïnstalleerd volgens de geldende instructies door een gecertificeerde
en getrainde Marmitek X-10 -dealer.
Copyrights
Marmitek is a trademark of Pattitude B.V., SAX35™ is a trademark of
Marmitek B.V. All rights reserved. Copyright and all other proprietary
rights in the content (including but not limited to model numbers,
software, audio, video, text and photographs) rests with Marmitek B.V.
Any use of the Content, but without limitation, distribution, reproduction,
modification, display or transmission without the prior written consent of
Marmitek is strictly prohibited. All copyright and other proprietary notices
shall be retained on all reproductions.
20360 - 2010929
Marmitek X-10
Potential-free actuator/interface
type SAX35
For connecting
external devices
to Marmitek X-10
PROG.
N
L
SAX
35
16
Marmitek X-10 Potential-free input/output interface type SAX35
Description
Module with:
Two galvanically separated potential-free inputs for
transposing contact outputs on external devices into
Marmitek X-10 power line commands.
One galvanically separated potential-free relay contact output
for transposing Marmitek X-10 power line signals for opening
and/or closing of a relay contact.
Connection
Mains connection via fixed mains cable.
Galvanically separated relay contact with 2 screw terminals:
normally open contact.
Galvanically separated inputs with 4 screw terminals with
common “+” connection.
Application
On one side, the module can be connected directly to the mains
and on the other side, via the built-in galvanic separation, to
peripheral equipment to send 2 Marmitek X-10 addresses and
receive 1 Marmitek X-10 address. The module must be
connected to other equipment such as a personal alarm system,
burglar alarm system or other equip ment to make this
equipment suitable for use with the Marmitek X-10 .
17
Operation
The SAX35 can transpose two galvanically separated contact
inputs to Marmitek X-10 addresses, plus on or off commands.
The addresses are defined by the programmed send address of
the module. The inputs are activated by an external DC or AC
voltage of 5 V to 25 V.
The SAX35 can also transpose a received Marmitek X-10
address plus command to open or close the relay contact. This
output is suitable for 5 A AC or DC.
Which Marmitek X-10 address is transposed is defined during
the programming of the SAX35. To do so the module needs to
be provided with a receive address. The relay contact is also
galvanically separated from the input wires.
Connection terminals
Description Explanation
Input 1 Programmed send address
(V+ on + with DC supply)
Input 2 Programmed send address +1
(V+ on + with DC supply)
Relay contact Programmed receive address
18
Programming
Always switch on the power before programming.
Avoid the contact with life parts!
Programming the SAX35
To define which Marmitek X-10 addresses correspond to the
inputs and relay contact, the SAX15 included in the SAX35
needs to be programmed.
The address of input 1 and the relay contact output can be
selected independently.
The second input is automatically allocated the next higher
address. Remember that the input and output addresses should
not overlap and ensure that the base input address is always at
least two higher than the base output address. If the base
address is set to 16, the second connected address will be 1.
Programming mode
Activating programming mode
The SAX35 needs to be set into programming mode as follows:
Press the program button for at least three seconds,
see Figure 1, so that the red LED lights up when the button
is released.
!
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek SAX35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek SAX35 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info