613067

Marmitek PC CONTROL REMOTE Manual

10
Zoom out
Zoom in
Previous page
1/56
Next page
10 MARMITEK
[23] Stop
In VCR, DVD or CD mode: This button works the same way as in your original remotes.
IN TV mode: Coloured key (Green), control of videotext or special equipment functions.
[24] REC (record )
This key works the same way as the one on your original remote for your VCR. In order to
avoid a mistake you have to press this key twice to activate this feature.
[25] Pause
In VCR, DVD or CD mode: This button works the same way as in your original remotes.
IN TV mode: Coloured key (Magenta), control of videotext or special equipment
functions.
4.2. Programming the TV, VCR , DVD, SAT and AUX modes
Note: you can dedicate any appliance (TV, DVD, SAT...) to the VCR, DVD, SAT,or AUX
keys: you just need to enter the 3 digit code (found in the code book) of the appliance,
i.e. a VCR code under the SAT key. In any case, follow the steps below:
1. Make sure your equipment is switched on (for example TV).
2. Press and hold the SETUP (4) key until the LED indicator lights continuously.
Release the SETUP key.
3.
Press and release the mode key (3) of the device you want to control (for example TV).
4. Enter the 3 digit code from the Code Book by using the key pad (11). The LED (2)
turns off after the last digit is entered. If you entered a wrong code the LED blinks
for 3 seconds and then goes off. You have to repeat from step 2.
5. Point the remote in the direction of your TV and press the POWER button (1).
Your device should turn off. Check other functions (for example for a VCR
FF or REW, etc.). If certain functions are not responding, this indicates that the
entered code is not the correct one. In that case repeat the above procedure with
the next corresponding code of your brand.
6. Repeat this procedure from step 1 for the other equipment you want to control
(VCR, DVD, SAT).
4.3. Manual code search
If your equipment (TV, SAT etc....) does not respond, try the other codes for your brand. If
it still doesn’t respond, try the manual code search method.
Note: as you can dedicate any appliance (TV, DVD, SAT...) to the VCR, DVD, SAT or AUX
keys, you first need to enter any 3 digit code for the kind of appliance you wish to control
(found in the code book), i.e.: If you want to program a SAT under the AUX key, enter
ANY SAT code found in the code book and then follow the steps below
1. Make sure your equipment is switched on.
2. Press and hold SETUP (4) until the LED indicator lights steadily. Release SETUP
3. Press the mode key (3) that matches the equipment you want to control
(for example TV).
4. Press Channel+ (9) repeatedly until the channel changes.
If you step past the correct code use Channel- (9) to go back to the right code.
5. When the equipment you want to control reacts press --/- (14) to confirm the code.
That’s all.
Note: If your equipment doesn't have Channel+ you can use PLAY (VCR or DVD) (22) or
POWER (1) key.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek PC CONTROL REMOTE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek PC CONTROL REMOTE in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info