494283

Marmitek DoorPhone 124 Manual

10
Zoom out
Zoom in
Previous page
1/100
Next page
10
© MARMITEK
If after you have logged on and you hear interference coming from other wireless devices in
the neighbourhood, such as a mobile phone, then repeat the above mentioned procedure or
switch over to another channel (when you change the channels, you will need to repeat the
pairing procedure).
When the pairing has not been successful (the ‘P’ symbol on the LCD screen will flicker),
then put off the handset and disconnect the power supply of the door unit by removing the
batteries. Repeat the pairing procedure.
4.1 Copying the ID code to an extra handset:
Beware! In case you have more than one handset, always first perform the pairing procedure
with one handset only. Use the logged-on handset to copy (‘clone’) the ID to the extra
handset(s). Every time you add an extra unit to the system, you need to copy the ID code to it;
otherwise the system will not function properly.
Follow the steps given below to copy the ID code onto an extra handset.
Make sure that the extra (‘Slave’) handset has been switched to the same channel as the primary
(‘Master’) handset (see chapter 3.2:’Channel settings handset’). Tip! All ‘Slave’ handsets can be
cloned to the ‘Master’ handset at the same time.
Step 1
Press and hold the buttons (8) and (9)
at the same time for a few seconds
to put on the handset. You will now
hear a short beep. Release (8) and (9)
buttons and you will hear a 2nd beep
as confirmation. You will see a ‘P’
flashing in the display.
Logged-on handset ‘Master’ To be cloned handset ‘Slave’
Step 2
Press on the call button (10) a
symbol
will appear on the
display. The saved ID code is
now being sent.
Step 3
Now press briefly on the on/off
button (8) to return to the normal
display.
Step 1b
Press and hold the buttons (8) and (9)
at the same time for a few seconds
to put on the handset. You will now
hear a short beep. Release (8) and (9)
buttons and you will hear a 2nd beep
as confirmation. You will see a ‘P’
flashing in the display.
Step 2b
The ‘P’ shall stop flashing within
5 seconds after the ‘Slave’ handset
has received the ID code, and will
beep twice briefly to indicate that
the cloning has been completed.
Step 3b
Now press briefly on the on/off
button (8) to return to the normal
display.
To activate the temperature reading, the batteries need to be removed from the door unit for
the duration of 5 seconds.
20194_20100216_UG_Doorphone120.i10 10 12-3-2010 9:52:37
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek DoorPhone 124 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek DoorPhone 124 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info