62166
62
Zoom out
Zoom in
Previous page
1/94
Next page
59
ENGLISH
(Using the remote controller)
When switching to M-DAX mode, press the AMP
button and then the > button until the PAGE 4 is
displayed.
When “M-DAX” is displayed on the remote controller,
press the M-DAX (D5) button.
Each time this button is pressed, M-DAX changes
as follows.
OFF LOW HIG
H
Notes:
M-DAX is compatible with PCM (48 kHz or lower)
and two-channel analog sources.
• The M-DAX is not available when Dolby Virtual
Speaker mode is being used.
VIDEO CONVERT
ANALOG VIDEO CONVERSION
This unit is equipped to convert video signals
for monitor output. Because of this, indifferent of
the connection (VIDEO, S-VIDEO, COMPONENT
VIDEO) between the playback device and this unit,
listening and viewing are possible with a single
higher grade cable between the MONITOR OUT
terminal of the unit and the monitor.
UP-CONVERSION FROM ANALOG VIDEO
SIGNALS TO HDMI
The up-conversion feature of this unit can output
the input analog video signals (for component video
signals of 480i, 480p, 1080i and 720p resolution, and
S-Video and Video (composite) of 480i resolution) to
the HDMI MONITOR terminal.
Notes:
HDMI video input is only output to the HDMI
MONITOR OUT terminal of the unit. If connecting
a playback device such as a DVD player to the
HDMI input jack, connect the HDMI MONITOR
OUT terminal of the unit to a TV monitor.
This mode is unavailable for the REC out terminal.
This mode is unavailable for still picture, fast
forward and reverse play on video component.
If, while attempting to use the video convert
feature, the unit cannot synchronize with the
display device, “NO SIGNAL” appears on the
monitor or noise is generated, this feature cannot
be used. All of these signs are caused by equipment
incompatibility; there is nothing wrong with the unit.
If this occurs, set “VIDEO CONVERT” in the
VIDEO SETUP” menu to “DISABLE”. Next,
connect the video input signal to the display component
via the MONITOR OUT terminal under VIDEO and
the S-video input signal to the display component via
the MONITOR OUT terminal under S-VIDEO.
The video convert feature constantly monitors
input video signals and determines whether to
convert the input signals or not. However, some
input video signals cannot be detected correctly.
If this occurs, set “VIDEO CONVERT” in the
VIDEO SETUP” menu to “DISABLE”.
For optimal video performance, THX recommends
setting the “VIDEO CONVERT” mode “DISABLE”.
CONNECTION EXAMPLE
When a monitor is connected to the HDMI
MONITOR OUT terminal of the unit
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8002
M-DAX
ENTER
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/OFF
VIDEO
or S-VIDEO
or component
HDMI
or HDMI
Notes:
If the resolution of the component video signal
input from the playback device is other than 480i,
480p, 1080i or 720p, images are not output from the
HDMI MONITOR OUT terminal of the unit.
If the resolution of the S-Video or Video signal input
from the playback device is other than 480i, images
are not output from the HDMI MONITOR OUT
terminal of the unit.
When a monitor is connected to the VIDEO or S-
VIDEO MONITOR OUT terminals of the unit
DIGITAL
RLVIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
VOLUME
UP
DOWN
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8002
M-DAX
ENTER
MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
POWER ON/OFF
L
C
R
SL S SR
LFE
DIGITAL
SURROUND
V-OFFDISP MULTI AUTO TUNED ST SPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
VIDEO
or S-VIDEO
VIDEO
or S-VIDEO
or component
HDMI
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
12
LIGHT
Learning Remote Controller
RC8001SR
AMP
D4
D5
D2
M
D1
D3
D5
VOL
CH
LEARN
NAME
MACRO
USE
PAGE
123
4
D4
D2
D3
D5
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote controller)
To
adjust the tone
, press the AMP button and press
the > button PAGE3 is displayed.
To adjust the bass effect, press BASS+ (D2) or
BASS– (D3).
To adjust the treble effect, TREB+ (D4) or TREB–
(D5).
Notes:
The tone control function is unavailable for the
Source Direct, Pure Direct, Headphone, Dolby
Virtual Speaker, THX mode, and 176.4/192kHz
PCM.
The tone control function is not available when
ACOUSTIC EQ is being used.
• Additionally, tone control is not available during
Dolby TrueHD, Dolby Digital Plus, or DTS-HD
playback.
TEMPORARILY TURNING OFF THE SOUND
2 31
5 64
8 97
OK
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
SLEEP
MUTE
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the remote controller.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording or
dubbing that may be in progress.
When the system is muted, the display will show
MUTE” .
Press the MUTE button again to return to normal
operation.
USING THE SLEEP TIMER
2 31
5 64
8
0
97
MEMO
CLEAR
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
9
SLEEP
To program this unit for automatic standby, press the
SLEEP button on the remote controller.
Each press of the button will increase the time before
shut down in the following sequence.
OFF 10 20 30 5040
100 90 80 70 60110120
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows “SLEEP OFF” and the
SLEEP indicator will disappear.
M-DAX (Marantz Dynamic Audio eXpander)
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
12
LIGHT
Learning Remote Controller
RC8001SR
AMP
D4
D5
D2
M
D1
D3
D5
VOL
CH
USE
PAGE
4
D4
D2
D3
D5
This function makes up for lost audio content in MP3
or AAC sources (from lossy compression) during
playback. Choose one of the following levels for this
effect as desired.
“HIGH”: Stronger effect
“LOW”: Weaker effect
“OFF”: Deactivated.
SR7002-8002_U_01_ENG 3_3.indd 59SR7002-8002_U_01_ENG 3_3.indd 59 07.8.24 1:15:59 PM07.8.24 1:15:59 PM
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR7002 in the language / languages: English as an attachment in your email.

The manual is 15,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz SR7002

Marantz SR7002 User Manual - Dutch - 74 pages

Marantz SR7002 User Manual - French - 84 pages

Marantz SR7002 User Manual - Spanish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info