522801
80
Zoom out
Zoom in
Previous page
1/96
Next page
NAMES AND
FUNCTIONS
78
BASIC
CONNECTIONS
BASIC
OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
If you have any problem using this product, please be sure to check the items in the following table.
If you trouble cannot be solved, please unplug the power cable immediately and contact your Marantz
authorized dealer or service center.
GENERAL
Symptom Cause Solution Page
The unit does not
turn on.
The AC power cable is improperly
connected.
Check the AC power cable
connection.
15
Make sure the AC power cable is
rmly inserted into the unit.
Make sure the power plug is fi rmly
inserted into the power outlet.
There is no sound.
The input cables are not fully
connected.
Check the connection of the input
cables between this unit and the
source component (CD player, etc.),
referring to the connection diagram.
12
The input selector is in the wrong
position.
Set the input selector to the input
terminal to which the source
component (CD player, etc.) is
connected.
16
The volume is too low. Adjust the volume.
The mute function has been
activated.
Cancel the mute function.
Headphones are connected to the
unit.
Remove the headphones.
41
There is no sound
from a certain
speaker.
The speaker is improperly
connected.
Refer to the connection diagram to
properly connect the speaker.
11
The sound image
does not localize
correctly and is
unnatural.
The polarity (+/–) of some
speaker cables is incorrect.
Speaker position and speaker
cable connections are incorrect.
Unplug the AC power cable
and check the speaker cable
connections.
11
The STANDBY
indicator is blinking
slowly (twice a
second).
The speaker cable has short-
circuited.
The unit was played at a higher
volume than it was designed to
be played.
You are using speakers with
lower impedance than required.
The unit was placed and used on
a narrow rack or similar confi ned
space and became overheated
inside.
Unplug the AC power cable
and check the speaker cable
connections.
Turn the volume down a bit.
Always use speakers with the
required impedance.
For safety's sake, always leave
enough space around the unit.
Use the remote controller to turn
on the power.
If the same problem occurs
again, unplug the AC power
cable and have the unit serviced
at the nearest service center.
11
16
11
3
6
The STANDBY
indicator is blinking
fast (8 times a
second).
There may be something wrong
with the unit.
Immediately unplug the AC power
cable and have the unit serviced at
the nearest service center.
Symptom Cause Solution Page
The display is not
displaying properly.
The unit uses a computer that on
rare occasions can malfunction
if affected by static electricity,
lightning or so on.
Unplug the AC power cable and
then plug it in again.
15
Cannot use the
remote controller
to operate the unit.
The batteries are dead.
Replace the batteries with new
ones.
3
The remote controller is out of
range.
Use the remote controller within
range of the unit.
4
There is an obstacle between the
unit and remote controller.
Remove the obstacle.
Strong light is falling on the unit's
infrared receptor window.
Prevent strong light from falling on
the infrared receptor window.
The mode of the remote controller
is improperly set.
Press the remote controller's AMP
button before operating.
16
The unit is set to IR = DISABLE.
Change the setting to IR =
ENABLE.
22
The main unit's
volume control
and buttons do not
work.
The front key (button) lock has
been set.
Release the front key (button) lock.
43
A hissing noise
(residual noise) is
generated when
there is no input
signal.
The unit has a surround DSP, which
can sometimes make a noticeable
hissing noise.
If the noise bothers you when
listening to a 2CH source, listen in
SOURCE DIRECT mode.
40
80


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR5004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR5004 in the language / languages: English as an attachment in your email.

The manual is 21,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info