522801
30
Zoom out
Zoom in
Previous page
1/96
Next page
NAMES AND
FUNCTIONS
28
BASIC
CONNECTIONS
BASIC
OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERSSETUP
ENGLISH
SETUP
HOW TO PERFORM AUTO SETUP
(AUDYSSEY MULTEQ
®
)
During this setup process, a GUI menu displays
important instructions. So be sure to connect and
power on the monitor to view the GUI instructions.
1. Connect the supplied microphone to the
SETUP MIC jack on the unit.
2. Set the microphone in the main listening
position.
Notes
Up to 6 positions around the main listening
position can be measured.
For the rst measurement, set the microphone in
the main listening position.
Use a stand or tripod to position the microphone
at ear height for all listening positions measured
with the microphone tip pointing directly up to the
ceiling.
• Remove any obstructions between the speakers
and microphone.
• When using a powered subwoofer, set the level
knob to the middle or 12 o'clock position. Set the
crossover to off, or to its highest value.
If the subwoofer has a standby, or sleep mode,
disable it. Not doing so could affect the test
signal which may result in inaccurate subwoofer
measurements.
During measurements, do not stand between the
microphone and the speakers. Make the room as
quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence
cell phones, televisions, radios, air conditioners,
uorescent lights, home appliances, light dimmers,
or other devices.
Cell phones should be placed away from all audio
electronics during the measurement process as
Radio Frequency Interference (RFI) may cause
measurement disruptions (even if the cell phone
is not in use).
It is suggested to operate the AUTO SETUP via
the remote controller rather than by front panel.
The test tones played through each channel
increase level as needed in order to overcome
ambient noise present in the listening environment
and obtain the best signal to noise ratio.
3. Select Speaker Setup” from the Main
Menu, select “Auto Setup” with the 3/4
cursor buttons, and press the ENTER button
to display the start screen.
4. Select the number of channels of the
surround back speakers which are being
used and whether height speakers are
part of the system. When a 5.1-channel
configuration is used for the speaker
systems, select “NONE” (no surround back
speakers and no front height speakers).
(See page 21, 36.)
Select Start” with the 3/4 cursor buttons
and press the ENTER button to start
measurement.
Audyssey MultEQ Setup
StartManual Setup
Front Height
Surround Back
Return
: Up / Down : Enter : OK Exit : Exit
: Yes
: 2ch
5. “1st Mic Position Check”
The main listening position refers to the most
central position where one would normally
sit within the listening environment.
MultEQ uses the measurements from this
position to calculate speaker distance,
level, polarity, and the optimum crossover
value for the subwoofer.
Audyssey MultEQ Setup
Cancel
Speaker Check :
-
-
1st Mic Position
Now Analyzing!!
: : Enter : OK Exit : Exit
Note
The Speakers Check detects the presence of
connected speakers. If a channel is not used, the
SPEAKERS CHECK will try to detect it, then
continue to the next channel.
6. When the 1st Mic Position Check ends, the
following GUI appears on the display.
Audyssey MultEQ Setup
Start
Check
Calculate
Speaker Check : OK
2nd Mic Position
: Up / Down : Enter : OK Exit : Exit
Here, to view the results of the detection
check, select “Check” with the 3/4 cursor
buttons and press the ENTER button. The
results will be displayed.
Speakers Configuration
Check Speaker Results
Front Left
Front Height Left
Center
Front Height Right
Front Right
Surround Right
Surround Back
Surround Left
Subwoofer
Return
: : Enter : Return Exit : Exit
: Yes
: No
: No
: No
: Yes
: Yes
: No
: Yes
: Yes
If Check Speaker Results indicates an error,
address the issue of the noted speaker
and remeasure. (For error messages, see
“ERROR MESSAGES” on page 30.)
After confi rming the check results, select
Return” with the 3/4 cursor buttons and
press the ENTER button to return to the GUI
menu.
At this point, you can select “Exit” to
end Auto Setup and return to “Speaker
Setup”.
Note
Auto Setup is not available in Pure Direct, Source
Direct, or 7.1 Channel Input modes.
7. Move the microphone to the 2nd listening
position, select “Start” with the 3/4 cursor
buttons and press the ENTER button to
measure the 2nd point. At this point, you
can cancel second point measurement
and calculate measurement results by
selecting “Calculate” and pressing the
ENTER button.
Audyssey MultEQ Setup
Start
Check
Calculate
Speaker Check : OK
2nd Mic Position
: Up / Down : Enter : OK Exit : Exit
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR5004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR5004 in the language / languages: English as an attachment in your email.

The manual is 21,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info