6528
15
Zoom out
Zoom in
Previous page
1/29
Next page
11
ENGLISH
ENGLISH
!1 PRE OUT Button
This button turns output from the PRE OUT jack on the
rear panel ON and OFF. When output is ON, the center of
the button is lit a blue color.
!2 REC OUT Button
This button turns the signals output from the RECORDER
1 and 2 OUT jacks on the rear panel ON and OFF. When
output is ON, the center of the button is lit a blue color. For
instructions on how to record, see RECORDING on pg.
16.
When RECORDER 1 is selected as the input source, sig-
nals are not output to the RECORDER 1 OUT jack. The
same goes for the RECORDER 2 OUT jack when RE-
CORDER 2 is selected as the input source.
!3 PHONO MC Button
This button switches the phono equalizer between MC and
MM. When MC is set, the center of the button is lit a blue
color. Set the phono equalizer amplifier according to the
type of cartridge you use.
!4 Side Illumination
The side illumination casts a blue light over switches and
buttons. It can be turned ON and OFF from the DISPLAY
button. For instructions on how to operate the side illumi-
nation, see HOW TO OPERATE THE SIDE ILLUMINA-
TION on pg. 18.
NAMES AND FUNCTIONS OF PARTS
DISPLAY
!5 Power Indicator
This indicator is lit a blue color while power to the PM-
11S1 is ON.
OPERATE
!6 Display Panel
Approximately 3 seconds after power
to the PM-11S1 is activated, the ID
set for the PM-11S1 is displayed here.
After that, the top line displays the in-
put source selected with either the IN-
PUT SELECTOR knob or the remote
controller, while the bottom line dis-
plays the volume level set with the
VOLUME knob or the remote control-
ler. When the PM-11S1 I is first activated, the attenuation
level (dB) is displayed for the initial volume level.
Volume Level Indication
The display panel also displays left-right level balance and
tone control trimming level. For instructions on how to ad-
just bass and treble, see How to Trim Bass and How to
Trim Treble on pg. 20.
The display panel also displays messages in response to
PM-11S1 operation.
!7 OPERATE Indicator
This indicator indicates the operating status of the PM-
11S1. When the ID is set to 0 for standalone operation, it
is lit a red color. When multiple PM-11S1s are connected
by FCBS, only the OPERATE indicator of the master PM-
11S1 (ID 1) lights a red color. Slave PM-11S1s whose
OPERATE indicator does not light a red color cannot be
used to operate other units in sync. For more information
on the FCBS, see ABOUT FCBS on pg. 17.
Also, the OPERATE indicator flashes if a protective circuit
trips. For troubleshooting procedures, see TROUBLE-
SHOOTING on pg. 22.
Max
0.5 dB steps
Min
Turn the VOLUME knob on
the PM-11S1 to the right or
press the VOLUME 3 button
on the remote controller.
Turn the VOLUME knob on
the PM-11S1 to the left or
press the VOLUME 4 button
on the remote controller.
PM-11S1N ENG(P09-P26)A4 04.8.17, 11:36 PMPage 11 Adobe PageMaker 6.5J/PPC
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz PM-11S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz PM-11S1 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info