571035
13
Zoom out
Zoom in
Previous page
1/20
Next page
FM broadcasts, turntable (PHONO), tape player,
or any other source capable of providing 200 mV
output level (AUX). The SELECTOR switch con-
nects the inputs of the TONE control amplifier
to the desired source.
TAPE 1 MONITOR SWITCH
The TAPE 1 MONITOR switch selects between
source and TAPE 1 INPUT jacks. When the TAPE
1 MONITOR switch is in its normal "out" posi-
tion, the preamplifier receives its input from the
SELECTOR switch. When the TAPE 1 MONI-
TOR switch is depressed,the preamplifier receives
its input from the TAPE 1 IN jacks.
PHONE EO AMPLIFIER
Phono signals of up to 100 mV can be handled
without overloading. The equalization network
provides precise equalization to the RIAA stand-
ard and sets the voltage gain of the phono pre-
amplifier to 40 dB (at 1 kHz).
MONO FUNCTIONS.
When the MONO pushswitch is in the "in" posi-
tion, the two channels are connected together
through mixing resistors. In addition, the left and
right channel tape input signals are connected
together through the same resistor network. This
facility allows all inputs to be converted to the
monophonic mode.
CONTROL CIRCUITS
The control circuits portion of the Model 2252
consists of the BALANCE, VOLUME, BASS,
MID, TREBLE, and HI FI LTER, controls. All
controls affect the left and right channels simulta-
neously. However, the BASS, MID and TREBLE
controls have clutched sections which allow indi- .
vidual adjustment of tonal balance for each
channel. With the controls set for flat response
and volume control at maximum, the overall volt-
age gain from any high-level input to the loud-
speaker terminals is approximately 41 dB.
BALANCE CONTROL
The BALANCE control is a full range control
which permits attenuation of each channel to
cutoff. The change of attenuation in each channel
as the control is moved from center has been
designed to maintain total apparent loudness
from both channels. This feature makes it a true
stereo balance control.
9
VOLUME CONTROL
The VOLUME control attenuates both channels
simultaneously and maintains tracking to within
3 dB at any point of attenuation to -60 dB from
maximum. Since the control is situated at the in-
put of the tone amplifier, there is no possibility
of overloading the amplifier stages under maxi-
mum rated output conditions. Thus, distortion is
kept to a minimum. After attenuation by the
BALANCE and VOLUME controls, the signal is
applied to the tone control amplifier.
TONE CONTROL AMPLIFIER
The TONE CONTROL AMPLIFIER's circuitry
uses a continuously variable negative feedback
type configuration for lowest distortion. The
signal from the TONE CONTROL AMPLIFIER
feeds the HI filter circuit when the HI FILTER
is activated.
AMPLIFIER
The amplifier section of the Model 2252 is a
direct coupled, full complimentary circuit. It
utilizes current limiting and thermal compensa-
tion circuits to provide safe, highly stable operat-
ing conditions. The silicone output devices used
in the power amplifier section provide a large
collector dissipation margin.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz Model 2252 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz Model 2252 in the language / languages: English as an attachment in your email.

The manual is 12,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info