571043
6
Zoom out
Zoom in
Previous page
1/13
Next page
01N Tape recorder jack (REC/PLAY)- The 5-pin
DIN tape recorder jack on the rear panel permits
use of European-type 5-wire tape recorder cables
with similarly equipped tape recorde"rs. This jack is
connected in parallel with the TAPE IN and TAPE
OUT jacks, but the polarizing pin in the plug
assures proper phasing at all" times.
TAPE OUT jacks-The signals available at this pair
of jacks may be routed to your tape recorder and
are affected only by the selector switch on th~
front panel.
TAPE IN jacks-With tape recorder pre-amplifier
outputs connected to these jacks, signals from a
tape recorder can be played through your system
when the recorder is set for playback mode of
operation and the TAP E MaN switch is in the IN
position.
AUX 1 jacks-These high level jacks provide for
connecting miscellaneous sources such as tape i
players with self-contained playback preamplifiers, I
phono cartridges that provided RIAA equal ized
high-level output, or additional tuners or receivers,
etc.
TUNER jacks-These high level jacks can be used
for connecting a stereo or mono tuner to the
Model 1060.
For stereo (multiplex) FM tuner reception, pro-
ceed asfollows:
Connect a pair of audio cables between the
tuner's right and left output jacks and the
Model 1060's right and left jacks. Set the
front panel selector switch to TUNER.
3
~.
1:.-f1iJJ{V{)
CW vJ 1~€:
Figure 2. Rear Panel Connection Facilities
For monophonic FM or AM tuners, proceed as
follows:
Connect one cable to either left or right
TUN ER jack. Set the front panel selector
switch to TUNER and depress both MONO
, IN (L,R) pushswitches.
;I~HONO jacks-These jacks are for use with stand-
ard phono cartridges requiring a 47,000 ohm
resistive load.
If hum is heard when playing records, it is evidence
of inadequate grounding or shielding of your
record player or connections. Connect a separate
ground wire from the turntable or record changer
frame to the CHASSIS GROUND binding post on
the Model 1060. If the tone arm is mounted on a
wood panel or is otherwise insulated from the
frame, connect the arm's mounting base to the
I grounding wire with a short jumper. If the two
pairs of signal wires in the arm have a single overall
shield, connect the shield to the grounding wire,
keep the two phono connecting cables and ground-
ing wire closely together. In three-wire (common
ground) systems, this will minimize "ground
loops".
If excessive phono hum persists, your
I phono cartridge may have a clip connecting the
I two "common" wires together, remove it.
I
I'
TAPE jacks-tOo not confuse the TAPE jacks with
the TAPE INor TAPE OUT jacks.) An extra tape
recorder can be connected to the TAPE jacks.
! When playing back with the tape recorder con-
~
nected to the TAPE jacks, place the selector switch
on the front panel in the TAPE position. The
I TAPE jacks are not affected by the TAPE MaN
pushswitch
on the front panel.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz Model 1060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz Model 1060 in the language / languages: English as an attachment in your email.

The manual is 8,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info