571043
5
Zoom out
Zoom in
Previous page
1/13
Next page
PREPARATIONFORUSE
Rear panel Signal Connection
All signal connections to the Model 1060 should be
made with shielded audio cables. Figure 2 shows
the location of the input and output jacks on the
rear panel. These are for "permanent" connections.
Use of the front panel controls and jacks will be
discussed later. A letter "L" corresponds to the left
audio channel; a letter "R" to right audio channel.
To avoid confusion, it is suggested that you
connect one cable at a time between the Model
1060 and the other components of your system.
This way, mixing up the channels or mixing up
signal sourcesand destinations will be avoided.
D
The SPEAKER SYSTEM (MAIN, REMOTE) jacks
on the left side of the rear panel will accomodate
two loudspeaker systems; each speaker having a
rated impedance between 4 and 16 ohms. When
using only one pair of speakers, connect them to
the terminals marked MAIN. The terminals marked
REMOTE are used for connection a second pair of
speakers in a location remote to the Model 1060.
u
Use care when connecting the Model 1060 to a
loudspeaker which contains a built-in power
supply-such as an electrostatic loudspeaker. The
"common" speaker-connection terminal of these
devices may be capacitively coupled through the
power supply. Ensure that the (-) terminals of the
model 1060 are connected to the "common"
SYSTEM 1 REPEAT WIRI NG
AS FOR SYSTEM 1
+
COM.
RIGHT
LEFT
Figure1. LoudspeakerSystem Connections
terminals of the loudspeaker system as shown in
Figure 1. Ordinary #18 gaugetwo-conductor lamp
cord may be used for distances of up to 30 feet
between amplifier and loudspeakers. For longer
distances, use#16 gaugewire or heavier, depending
on length.
In connecting two loudspeakers for stereo opera-
tion, it is important to insure correct relative
phasing (polarity). This is best acheived, when
using identical loudspeakers, by simply coding each
wire for identification, one wire in each pair
should be coded at both ends with a knot, tape,
etc. The coded wires can then be used for identical
connections in each channel. For example, the
coded wire in each pair can be connected to the
"common" terminal of each loudspeaker and the
(-) terminal of each amplifier channel. The un-
coded wire of each pair is then connected to the
remaining loudspeaker terminal and the remaining
terminal on each amplifier channel (R and L). This
procedure insures correct polarity or phasing of
identical loudspeakers.
Note: Close inspection of standard zipcord will
reveal some form of coding on the insulation (ridge
or groove on one edge); or one of the wires may be
tinned and the other wire not tinned.
CAUTION: Never directly connect the loudspeaker
terminals of one channel in parallel with those of
any other. Any resulting damage is not covered
under warranty.
2
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz Model 1060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz Model 1060 in the language / languages: English as an attachment in your email.

The manual is 8,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info