742782

Marantec Control x.51 Manual

51
Zoom out
Zoom in
Previous page
1/58
Next page
Error Cause Solution
Message 3 - Closing edge safety device OPEN was
activated.
- Remove the obstacle or have the closing edge safety device
checked.
- Deactivate or connect the closing edge safety device.
Message 5 - Closing edge safety device CLOSE was
activated.
- Remove obstacle or have the closing edge safety device
checked.
- Deactivate or connect the closing edge safety device.
Message 7 - If no buttons are pressed within 120 seconds, the programming mode terminates automatically.
- OPEN and CLOSED gate positions programmed without passing the reference point.
Message 8 - Reference point button defective. - Have the operator system checked.
Message 9 - No speed sensor impulses,
drive system is blocked.
- Have the operator system checked.
Message 10 - Gate movement too stiff.
- Gate blocked.
- Ensure that the gate moves easily.
- Maximum driving power setting is too
low.
- Have the max. driving power (Section 9.4 / Level 2 /
Menu 1+2) checked by an expert.
Message 11 - Excess travel stop. - Have the operator system checked.
Message 12 - CESD test in OPEN direction not OK. - Check closing edge safety device.
- Programme out the closing edge safety device if there is no
CESD present (Section 9.4 / Level 8 / Menu 2).
- Reinsert an 8.2 kOhm resistance.
Message 13 - CESD test in CLOSED direction not OK. - Check closing edge safety device.
- Programme out the closing edge safety device if there is no
CESD present (Section 9.4 / Level 8 / Menu 2).
- Reinsert an 8.2 kOhm resistance.
Message 15 - External photocell interrupted or
defective.
- Remove obstacle or have the photocell checked.
- Programmed for photocell, but no
photocell is connected.
- Deactivate or connect the photocell.
10.3.2
Malfunctions with error messages
10. Messages
Operating Instructions, Comfort 580 GB (#91636) 51
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Control x.51 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Control x.51 in the language / languages: English as an attachment in your email.

The manual is 3,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantec Control x.51

Marantec Control x.51 User Manual - German - 58 pages

Marantec Control x.51 User Manual - German - 58 pages

Marantec Control x.51 User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info