743674

Marantec Control 300 Manual

5
Zoom out
Zoom in
Previous page
1/20
Next page
5
E N G L I S H
1. Parts supplied:
Control 300 traffic light controls in separate housing with two red and green traffic lights, connecting flange and
cable harness for connection to the Control 110 base control unit.
2. Description of operation:
Entry and exit are separately controlled. After an impulse has been given with the door closed, both red traffic lights
light up until the door has reached its final "open" position. Then the side on which the impulse was given changes
to "green". The traffic light on the other side stays at "red". All further impulses with the door open are stored, so
that the direction of the traffic is controlled via the traffic lights. In the case of heavy traffic from the one direction,
the green phase changes to the other direction if required. After all the stored impulses have been actioned, both red
traffic lights light up, the door closes automatically after the set red time has elapsed. Both red traffic lights go out.
3. Setting the "red time" and the "green time":
The "red time" and the "green time" are set with the rotary switches on the front of the housing.
4. Control sequence:
4.1. An impulse is given by push button, key switch or induction loop etc. The following control sequences are possible:
a) If an impulse is given to terminals 43-44 or 45-46 of the Control 300, with the door closed, the door opens.
b) If an impulse is given to terminals 43-44 or 45-46 with the door open, the "green time" is extended, as the timing
for opening is restarted.
c) If an impulse is given to terminals 43-44 or 45-46 while the door is closing, the door stops for one second, and
then starts to open again.
If the impulse is given in the Control 110 base control unit (e.g. to terminals 14-15), there is also opening and
automatic closing with the red traffic lights on, but without any green phase or change of direction during the
closing process.
4.2 Photocell as safety device:
The photocell is connected to the terminals 41-42 of the Control 300 traffic light controls. If the photocell is
interrupted, this activates the control sequences described under 4.1 b) and c). With the "S" switch on the
board, the following photocell functions can be set:
"S" ON door stops on interruption of photocell
"S" OFF door stops on interruption of photocell and after one second reopens.
4.3. Switching off the automatic closing function (timed return). The automatic closing function can be switched off by
connecting an ON/OFF switch or by attaching a bridge to terminals 47-48 of the Control 300 traffic light controls.
5. Connection:
Connect the Control 300 cable harness to the Control 110 base control unit. The S19 programming switch in the
Control 110 base control unit must be in the OFF position. A fuse for safeguarding the electronic equipment and the
traffic lights is situated on the board of the traffic light controls.
Function of the Control 300 connecting terminals:
L1, N, PE: Mains connection 220 V, 50 Hz
1a,1b,N: Connection of traffic lights-exit
2a,2b,N: Connection of traffic lights-entry
V: Motor phase V door drive
12a,13a: "Stop" contact for basis control unit
13a,36: "Impulse" contact for basis control unit
5, 37: Limit switch "close"
5, 39: Limit switch "open"
41,42: Photocell connection
43,44: Impulse push button, pull button - exit
45,46: Impulse key switch, push button - entry
47,48: Automatic closing function (timed return) ON/OFF
Important:
Please observe local safety regulations!
Control voltage 24 V DC
Always lay mains cable and control cable separately!
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Control 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Control 300 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info