743220
7
Zoom out
Zoom in
Previous page
1/29
Next page
7
N1 Mains filter
R1,R2,R3 Resistors
S Photocell stop (ON)/Um (OFF)
S32 Automatic "ON/OFF" (if installed)
S33 "Impulse" button
T1 Transformer
V1,V3,V4 Optocouplers
V2 Mains rectifier
X8 Control 210 terminal block
X8a,X8b Plug-in terminal block
a On installing the photocell, remove bridge a.
I. Operating the week timer
A. Connection
Connect the timer.
The integrated battery will now be charged. When symbols start to appear in the display (after approximately two
minutes), operate the "Reset" button with a pencil or similar instrument. OFF 00:00 will appear in the display.
The timer is now ready for operation.
B. Setting the day and the correct time
1. Keep the button depressed during the entire procedure!
2. With button "h+" and "m+", enter the current time of day ("h+" = hours/"m+" = minutes)
3. If the buttons "h+" and "m+" are kept depressed for longer than 1 second, the display automatically increases the
count.
4. Use the "day" button to set the current day of the week (appears in the display).
5. Release the button and the time starts running - indicated by the two flashing dots in the display.
II. Programming the switching times (alter or delete)
A. Programming the switch-on time
The TIMER OFF symbol --:-- is shown in the display. By proceeding as described under point 1.B (setting the time of
day), enter the time, at which the automatic timed return is to be switched on.
On having entered the time, press the "Timer" button to store the command in the program memory. The symbol
TIMER ON --:-- appears in the display.
B. Programming the switch-off time
Press the "Timer" button once. The entered time disappears from the display, and the symbol TIMER ON --:--
appears. By proceeding as described under point 1.B (setting the time of day), enter the time, at which the automatic
timed return is to be switched off. Now enter the day, on which the switch-off command is to be carried out. If you
wish this switching time command to be carried out on more than one day, please read the following sections. Now
press the "Timer" button again to store the command in the program memory. The symbol TIMER OFF --:--
appears in the display.
C. To enter further switching times - ON or OFF, press the "timer" button once, or if required more than once. A free
storage space will be shown in the display: e.g. TIMER ON --:--. Enter the switching times as described under II. In the
aforementioned manner as many as 6 switch-on and 6 switch-off times can be programmed.
D. Weekday block formation
With the "Day" button, besides individual days of the week, combinations of two or more days can also be
programmed.
1. Monday - Friday
2. Saturday + Sunday
3. Monday - Saturday
If no specific day of the week is assigned to the switching commands, then these are carried out daily. If a single day
or one of these day combinations is stored in the memory as a constituent part of the program, this means that the
switching command entered will be carried out on each of these weekdays at the same time. In order to get from
the programming mode directly to the time of day, interrupt the programming and press the button .
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Control 210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Control 210 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info