743220

Marantec Control 210 Manual

6
Zoom out
Zoom in
Previous page
1/29
Next page
6
E N G L I S H
1. Parts supplied:
Control 210 automatic timed return in separate housing with two red traffic lights, connecting flange and cable
harness for connection to Control 110 base control unit.
2. Description of operation:
After an impulse has been given with the door closed, both lights flash until the door has reached its final "open"
position. The two lights then go out and the door remains open in accordance with the set "open" time. Once this
time has elapsed, the two lights flash for the duration of the set prewarning phase. Afterwards the door
automatically closes and both lights go out.
3. Setting the "prewarning" and "open" times
The "prewarning" and "open" times are set by means of the rotary switches on the front of the housing.
4. Control sequence:
4.1. An impulse is given by push button, key switch or induction loop etc. The following control sequences are possible:
a) If, with the door closed, an impulse is given to the terminals 43-44 of the Control 210, the door opens.
b) If, with the door open, an impulse is given to terminals 43-44, the opening time is extended, as the timing
for opening is restarted.
c) If, while the door is closing, an impulse is given to terminals 43-44, the door stops for one second, and then
opens again.
If the impulse is given in the Control 110 base control unit (e.g. to terminals 14-15), this cancels out the possibility of
extending the opening time with the door open or of changing the direction while the door is closing.
4.2 Photocell as safety device:
The photocell is connected to terminals 41-42 of the Control 210 automatic timed return (closing function). If the
photocell is interrupted, this activates the control sequences described under 4.1 b) and c). By means of the "S"
switch on the board, the following photocell functions can be set:
"S" ON door stops on interruption of photocell
"S" OFF door stops on interruption of photocell and after one second reopens.
4.3. Switching off the automatic timed return (closing function).
The automatic timed return can be switched off by connecting an ON/OFF switch or by attaching a bridge to
terminals 45-46 of the Control 210 automatic timed return.
5. Connection:
Connect the Control 210 cable harness to the Control 110 base control unit. The S19 programming switch in the
Control 110 base control unit must be in the OFF position. A fuse for safeguarding the electronic equipment and the
red traffic lights is situated on the board of the automatic timed return.
Function of the Control 210 connecting terminals:
L1, N, PE: Mains connection 220 V, 50 Hz
1,2,N: Connection for red traffic lights
V: Motor phase V door drive
12a,13a: "Stop" contact for door controls
13a,36: "Impulse" contact for door controls
5, 37: Limit switch "close"
5, 39: Limit switch "open"
41,42: Photocell connection
43,44: "Impulse" push button, key switch
45,46: Automatic timed return function on/off
Important:
Please observe local safety regulations!
Control voltage 24 V DC
Always lay mains cable and control cable separately!
6. Overview of Control 201 circuit diagram:
F1a Fuse 50 mA
F1b Fuse 4A max.
H40 Green LED "open"
H41,H42 Red traffic lights (entry/exit)
KL Photocell 24 V
K41 "Flashing" relay
K43 "Stop" relay
K44 "Impulse" relay
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Control 210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Control 210 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info