742639
11
Zoom out
Zoom in
Previous page
1/33
Next page
11
S13 Limit switch „close“
S14 Limit switch „DW-UM“
S16, S17 Programming „Digital 131”
S18 Programming switch 2nd stop switch X2d
S19 Programming switch Control 200/Control 300
S20 Programming switch photocell
S21 Change-over airswitch contact/closing edge safety device with optosensor
T1 Transformer
V1 Mains supply circuit
X1 Power cable 3 - 220 V/380 V 50 Hz
X1a Power cable 3 - 220 V 50 Hz
X2,X2a-e Connecting terminal block „Control 100 base control unit“
X2f Plug-in connection „Control 100 base control unit“
X3 Terminal block „drive“
X4 Plug-in stip „remote control“
X5 Plug-in connection „keypad circuit board“
X7 Connecting terminal safety device
X7a Connecting terminal safety device „Dynamic“ shaft drive*
* if included
Factory-bridged terminals, programming switch
Designation Terminal block Bridged terminals Programming switch
Cable slack device X2b 6 - 7 -
1st „stop“ switch S0 X2c 1 2 - 13 -
2nd „stop“ switch S0a X2d - S18
Photocell KL - S20
Autom. timed return
Control 200 X2f - S19
Traffic light Control 300 X2f - S19
Wicket door X7a a -
On connecting the above listed additional devices, remove bridges or switch programming switch to OFF.
Cabling for motor, limit switches, closing edge safety device to be carried out on site.
Important:
Observe local safety regulations!
Control voltage 24 V DC
Change-over switch self-hold
S7 S8
„open“ direction „close“ direction
OFF OFF A2: open/close without self-hold
ON OFF A3: open with self-hold, close without self-hold
OFF ON A4: open without self-hold, close with self-hold
ON ON A6: open/close with self-hold
Change-over switch S21 Pre-set for „Digital 131“ at the
factory
closing edge safety device with airswitch (DW) contact S17
closing edge safety device with optosensor S16
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Control 103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Control 103 in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info