680457
14
Zoom out
Zoom in
Previous page
1/24
Next page
14 Operating instructions, Comfort 50, 60 (#104172 – GB)
5.4.2 Checking the automatic cut-out
WARNING!
Danger of injury due to incorrectly programmed values for
the door driving power!
Check the automatic cut-out function in the OPEN and CLOSE
directions.
Automatic cut-out in the OPEN direction
During travel, apply a load of 20 kg to the door at the mid point of
the bottom edge of the door:
The door should stop immediately.
Automatic cut-out in the CLOSE direction
Placeanobject,50mminheight,ontheoor.
Drive the door towards the obstacle:
The operator system should stop and reverse when it touches the
obstacle.
The settings for the driving power in the OPEN and CLOSE directions
remain saved even if the mains power supply is interrupted.
The parameters are returned to the factory settings only after a reset.
“Menu 11 - RESET“
5.4.3 Checking the photocell
Photocell
Check all the photocells individually by triggering them.
Check all the photocells just before the door reaches the CLOSED
position.
Special points regarding door-frame photocells
A door-frame photocell must function above the position at which
it is installed. Below the installation position, the function of the
photocell is suppressed by the control unit.
If several photocells are connected, all the photocells function in
the same way as a door-frame photocell, if present.
5.5 Special programming
DANGER!
Danger of injury due to incorrect settings for the door
driving power!
The DIN EN 13241-1 and EN 12453 provide limits for the protection
of people. These can be exceeded by selecting the wrong parameters.
It is therefore essential to test the force generated by the door.
Check the programmed parameter values.
“5.4.2 Checking the automatic cut-out“
Havethedrivingforcetestedbyqualiedandtrained
professionals with a force tester designed for this purpose.
Material damage resulting from incorrect programming of
the door operator.
After a reset, all the parameters are returned to the factory settings.
Safety elements that are operational and are connected to the system
will be recognised anew after a reset.
To ensure that the controls functions properly:
Reprogram all the required functions.
Reprogram the remote control.
Drive the operator system once to the OPEN position and then the
CLOSED position.
If a photocell is connected, it will be automatically detected by the
control system as soon as the power supply is connected.
The photocell can be reprogrammed later.
Photocells that are not required must be disconnected before the
power supply is connected; otherwise they will be recognised by the
controls.
“4.3.3 Terminal block XB03“
CHECK
A function test must be carried out after changes have been made in
programming mode.
“5.4 Function test“
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Comfort 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Comfort 50 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantec Comfort 50

Marantec Comfort 50 User Manual - German - 24 pages

Marantec Comfort 50 User Manual - Dutch - 24 pages

Marantec Comfort 50 Installation Guide - Dutch - 24 pages

Marantec Comfort 50 User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info