657962

Makita TD111D Manual

7
Zoom out
Zoom in
Previous page
1/68
Next page
7 ENGLISH
Changing the impact force
►Fig.7: 1. Hard 2. Soft 3.Amode4. Changed in three
steps 5. Button
Youcanchangetheimpactforceinthreesteps:hard,
soft,andAmode.
Thisallowsatighteningsuitabletothework.
Everytimethebuttonispressed,thenumberofblows
changes in three steps.
“Amode(assistmode)”isaneasy-to-usemodefor
driving screws with good control.
In this mode, the tool drives a screw with low-speed
rotationatrst.Afterthetoolstartstoimpact,therota-
tionspeedincreasesandreachesthemaximumspeed.
Forapproximatelyoneminuteafterreleasingtheswitch
trigger, the impact force can be changed.
Impact force grade displayed
on panel
Maximum blows Purpose Example of application
Hard
3,900 min
-1
(/min) Tighteningwhenforceand
speed are desired.
Tighteningwoodscrews,
tightening bolts.
Soft
1,600 min
-1
(/min) Tighteningwithlessforceto
avoid screw thread breakage.
Tighteningsashscrews,tight-
ening small screws such as M6.
Amode
3,900 min
-1
(/min) Tighteningscrewswithbetter
control.
Tighteninglongscrews.
NOTE:Amodeisavailableonlywhenthetoolrotatesclockwise.WhenrotatingcounterclockwiseinAmode,the
impact force and speed are the same as hard mode.
NOTE:Whenalllampsontheswitchpanelgoout,thetoolisturnedofftosavethebatterypower.Theimpactforce
gradecanbecheckedbypullingtheswitchtriggertotheextentthatthetooldoesnotoperate.
NOTE:Whilepullingtheswitchtrigger,theimpactforcegradecannotbechanged.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
socket bit
Optional accessory
►Fig.8
Useonlydriverbit/socketbitthathasinsertingportionshown
inthegure.Donotuseanyotherdriverbit/socketbit.
For tool with shallow driver bit hole
A=12mm
B=9mm
Use only these type of driver
bit. Follow the procedure
1. (Note) Bit-piece is not
necessary.
For tool with deep driver bit hole
A=17mm
B=14mm
Toinstallthesetypesofdriver
bits, follow the procedure 1.
A=12mm
B=9mm
Toinstallthesetypesofdriver
bits, follow the procedure 2.
(Note) Bit-piece is necessary
for installing the bit.
1. Toinstallthedriverbit,pullthesleeveinthedirec-
tion of the arrow and insert the driver bit into the
sleeve as far as it will go.
Thenreleasethesleevetosecurethedriverbit.
►Fig.9: 1. Driver bit 2. Sleeve
2. Toinstallthedriverbit,pullthesleeveinthedirec-
tion of the arrow and insert the bit-piece and driver
bitintothesleeveasfarasitwillgo.Thebit-piece
should be inserted into the sleeve with its pointed
endfacingin.Thenreleasethesleevetosecure
the driver bit.
►Fig.10: 1. Driver bit 2. Bit-piece 3. Sleeve
Toremovethedriverbit,pullthesleeveinthedirection
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case, try re-inserting the bit according to the instruc-
tions above.
NOTE:Afterinsertingthedriverbit,makesurethatit
isrmlysecured.Ifitcomesout,donotuseit.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita TD111D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita TD111D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 11,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info