Manual Makita TD 021D (page 5 of 40) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448659

Zoom out

Zoom in

1/40

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

• Always switch off the tool before insertion or removal of

the battery cartridge.

Installing or removing battery cartridge (Fig. 1)

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Lock lever (Fig. 2)

When the lock lever is in the locked position , the

switch cannot be actuated.

When the lock lever is in the unlocked position , the

switch can be actuated.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch actuates properly

and returns to the “OFF” position when released.

To start the tool, first move the lock lever to the unlocked

position to release the switch lever. (Fig. 3)

And then turn the switch to A side for clockwise rotation

or to B side for counterclockwise rotation. (Fig. 4)

Tool speed is increased by increasing rotation force on

the switch. Release the switch to stop.

CAUTION:

• Always check the direction of rotation before operation.

• Change the direction only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the lock lever in

the locked position .

Lighting up the front lamp

CAUTION:

• Do not look in the light or see the source of light

directly.

To start the tool, first move the lock lever to the released

position to release the switch. (Fig. 5)

To put on the light only, rotate the switch to the A or B

side a little.

To not only put on the light but also start the tool rotate

the switch to the A or B side more.

Release the switch to stop the lamp and tool. (Fig. 4)

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

ASSEMBLY

CAUTION:

• Always be sure that the lock lever is in the locked posi-

tion mark and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit or socket bit

Use only the driver bit or socket bit shown in the figure.

(Fig. 6)

Do not use any other driver bit or socket bit.

For European and North & South American coun-

tries, Australia and New Zealand

For other countries

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit.

(Fig. 7)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 8)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

OPERATION

The tool can be used in two ways; a straight type and a

pistol type which is selectable according to the conditions

of workplace and screwdriving. (Fig. 9)

CAUTION:

• When bending the tool to use in the pistol type or

straightening to use in the straight type, do not hold the

bendable part of the tool. Failure to do so may cause

your hand and fingers to be pinched and injured by this

part.

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 10 & 11)

A=12mm

B=9mm

Use only these types of bits. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A= 17mm

B= 14mm

To install these types of bits, follow the

procedure (1).

(Note) Makita bits are these types.

A= 12mm

B= 9mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for install-

ing the bit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita TD 021D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita TD 021D Manual

Product: