Manual Makita SA7000 (page 4 of 44) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598934

Zoom out

Zoom in

1/44

ENGLISH

Explanation of general view

1 Shaft lock

2 Lock lever

3 Switch trigger

4 Lock nut

5 Abrasive disc

6 Rubber pad

7 Lock nut wrench

8 Shaft lock

9 Exhaust vent

10 Inhalation vent

11 Commutator

12 Insulating tip

13 Carbon brush

14 Brush holder cap

15 Screwdriver

SPECIFICATIONS

Model SA7000

Disc diameter ..................................................... 180 mm

Spindle thread .......................................................... M14

No load speed (min-1) ............................................ 5,500

Overall length ..................................................... 453 mm

Net weight ............................................................. 3.3 kg

Safety class ............................................................. /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for the sanding of large surface of

wood, plastic and metal materials as well as painted sur-

faces.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.49 Ohms it can be presumed that

there will be no negative effects.

The mains socket used for this device must be protected

with a fuse or protective circuit breaker having slow

tripping characteristics.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to sander safety rules. If you use this tool unsafely or

incorrectly, you can suffer serious personal injury.

Safety Warnings Common for Sanding Operation:

1. This power tool is intended to function as a

sander. Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

serious injury.

2. Operations such as grinding, wire brushing, pol-

ishing or cutting-off are not recommended to be

performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. The arbour size of backing pads or any other

accessory must properly fit the spindle of the

power tool. Accessories with arbour holes that do

not match the mounting hardware of the power tool

will run out of balance, vibrate excessively and may

cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as backing pad

for cracks, tear or excess wear. If power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After inspect-

ing and installing an accessory, position your-

self and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute. Dam-

aged accessories will normally break apart during

this test time.

8. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small workpiece frag-

ments. The eye protection must be capable of stop-

ping flying debris generated by various operations .

The dust mask or respirator must be capable of fil-

trating particles generated by your operation. Pro-

longed exposure to high intensity noise may cause

hearing loss.

9. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of opera-

tion.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita SA7000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita SA7000 Manual

Product: