Manual Makita LS1219L (page 19 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691824

Zoom out

Zoom in

1/192

19 ENGLISH

INSTALLATION

Installing the grip

Screw the threaded shaft of the grip into the turn base.

►Fig.4: 1. Grip 2. Turn base

Installing the dust extraction hose

Connect the dust extraction hose to the tool as

illustrated.

Makesurethattheelbowandthesleevetproperlyto

the ports of the tool.

►Fig.5: 1. Dust extraction hose 2. Elbow 3. Sleeve

4. Port

Bench mounting

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. While lowering the

handle slightly, pull the stopper pin and rotate it 90°.

►Fig.6: 1. Locked position 2. Unlocked position

3. Stopper pin

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool's

base.Thiswillhelppreventtippingandpossibleinjury.

►Fig.7: 1. Bolt

WARNING: Ensure that the tool will not move

on the supporting surface. Movement of the miter

saw on the supporting surface while cutting may

resultinlossofcontrolandseriouspersonalinjury.

FUNCTIONAL

DESCRIPTION

WARNING: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool. Failure to switch off

and unplug the tool may result in serious personal

injuryfromaccidentalstart-up.

Blade guard

►Fig.8: 1. Blade guard

When lowering the handle, the blade guard rises auto-

matically. The guard is spring loaded so it returns to

its original position when the cut is completed and the

handle is raised.

WARNING: Never defeat or remove the blade

guard or the spring which attaches to the guard.

Anexposedbladeasaresultofdefeatedguarding

mayresultinseriouspersonalinjuryduringoperation.

In the interest of your personal safety, always maintain

thebladeguardingoodcondition.Anyirregularopera-

tion of the blade guard should be corrected immediately.

Check to assure spring loaded return action of guard.

WARNING: Never use the tool if the blade

guard or spring are damaged, faulty or removed.

Operation of the tool with a damaged, faulty or

removedguardmayresultinseriouspersonalinjury.

If the see-through blade guard becomes dirty, or saw-

dust adheres to it in such a way that the blade and/or

workpiece is no longer easily visible, unplug the saw and

clean the guard carefully with a damp cloth. Do not use

solvents or any petroleum-based cleaners on the plastic

guard because this may cause damage to the guard.

If the blade guard is especially dirty and vision through

the guard is impaired, unplug the tool and use the sup-

plied wrench to loosen the hex bolt holding the center

cover. Loosen the hex bolt by turning it counterclock-

wise and raise the blade guard and center cover. With

the blade guard so positioned, cleaning can be more

completelyandefcientlyaccomplished.Whencleaning

is complete, reverse procedure above and secure bolt.

Do not remove spring holding blade guard. If guard

becomes discolored through age or UV light exposure,

contact a Makita service center for a new guard. DO

NOTDEFEATORREMOVEGUARD.

►Fig.9: 1. Center cover 2. Hex wrench 3. Blade

guard

Kerf boards

This tool is provided with the kerf boards in the turn

base to minimize tearing on the exit side of a cut. The

kerfboardsarefactoryadjustedsothatthesawblade

doesnotcontactthekerfboards.Beforeuse,adjustthe

kerf boards as follows:

►Fig.10: 1. Kerf board

►Fig.11: 1. Left bevel cut 2. Straight cut 3. Right

bevel cut 4. Saw blade 5. Blade teeth

6. Kerf board

My saw will not auto lock and the bevel latch will not move help please Submitted on 30-12-2022 at 17:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1219L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS1219L Manual

Product: