Manual Makita LS1219L (page 18 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691824

Zoom out

Zoom in

1/192

18 ENGLISH

5. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

6. To reduce the risk of injury, return carriage

to the full rear position after each crosscut

operation.

7. Always secure all moving portions before

carrying the tool.

8. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

9. Check the blade carefully for cracks or dam-

age before operation. Replace cracked or dam-

aged blade immediately. Gum and wood pitch

hardened on blades slows saw and increases

potential for kickback. Keep blade clean by

rst removing it from tool, then cleaning it with

gum and pitch remover, hot water or kerosene.

Never use gasoline to clean blade.

10. While making a slide cut, KICKBACK can

occur. KICKBACK occurs when the blade

binds in the workpiece during a cutting oper-

ation and the saw blade is driven rapidly

towards the operator. Loss of control and seri-

ous personal injury can result. If blade begins

to bind during a cutting operation, do not con-

tinue to cut and release switch immediately.

11. Use only anges specied for this tool.

12. Be careful not to damage the arbor, anges

(especially the installing surface) or bolt.

Damage to these parts could result in blade

breakage.

13. Make sure that the turn base is properly

secured so it will not move during operation.

Use the holes in the base to fasten the saw to a

stable work platform or bench. NEVER use tool

where operator positioning would be awkward.

14. Make sure the shaft lock is released before the

switch is turned on.

15. Be sure that the blade does not contact the

turn base in the lowest position.

16. Hold the handle rmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

17. Make sure the blade is not contacting the

workpiece before the switch is turned on.

18. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced blade.

19. Stop operation immediately if you notice any-

thing abnormal.

20. Do not attempt to lock the trigger in the "ON"

position.

21. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

22. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

Additional safety rules for the laser

1. LASER RADIATION, DO NOT STARE INTO THE

BEAM OR VIEW DIRECTLY WITH OPTICAL

INSTRUMENTS, CLASS 2M LASER PRODUCT.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

PARTS DESCRIPTION

►Fig.2

1 Slide pole 2 Stopper pin (for carriage

sliding)

3 Vertical vise 4 Releasing button (for

right side bevel angle)

5 Holder 6 Turn base 7 Pointer (for miter angle) 8 Miter angle scale

9 Kerf board 10 Blade case 11 Adjustingscrew(for

laser line)

12 Rangeadjustmentscrew

(for laser line)

13 Blade guard 14 Knob (for bevel angle) 15 Hex wrench 16 Adjustingscrew(for

lower limit position)

17 Adjustingbolt(formaxi-

mum cutting capacity)

18 Stopper arm 19 Lock lever (for turn base) 20 Releasing lever (for turn

base)

21 Grip (for turn base) - - - - - -

►Fig.3

1 Switch trigger 2 Lock-off button 3 Hole for padlock 4 Switch (for laser line)

5 Hose (for dust

extraction)

6 Stopper pin (for carriage

elevation)

7 Guide fence (lower

fence)

8 Guide fence (upper

fence)

9 Dust bag 10 0°adjustingbolt(for

bevel angle)

11 Bevel angle scale 12 Releasing lever (for 48°

bevel angle)

13 Latch lever (for bevel

angle)

14 Pointer (for bevel angle) 15 45°adjustingbolt(for

bevel angle)

- -

My saw will not auto lock and the bevel latch will not move help please Submitted on 30-12-2022 at 17:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1219L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS1219L Manual

Product: