476899
15
Zoom out
Zoom in
Previous page
1/86
Next page
15
STORAGE
When keeping the machine in storage for a long time, drain fuel from the
fuel tank and carburetor, as follows: Drain all fuel from the fuel tank.
Remove the spark plug and add a few drops of oil into the spark plug hole.
Then, pull the starter gently to confirm that oil film covers the engine inside
and tighten the spark plug.
Clear dirt or dust from the cutter blade and outside of engine, wipe them
with a oil-immersed cloth and keep the machine at a place as dry as
possible.
MAINTENANCE SCHEDULE
General
Engine assembly,
screws and nuts
Visual inspection for damage and tightness
Check for general condition and security
After each refuelling
Throttle lever
Safety lock key
STOP switch
Functional check
Functional check
Functional check
Daily
Air filter
Cooling air duct
Cutting tool
Idling speed
To be cleaned
To be cleaned
Check for damage and sharpness
Inspection (cutting tool must not move)
Weekly
Spark plug
Muffler
Inspection, replace if necessary
Check and if necessary clean the opening
Quarterly
Suction head
Fuel tank
To be replaced
To be cleaned
Shuting down
procedure
Fuel tank
Carburetor
Empty fuel tank
Operate until engine runs out of fuel
FAULT LOCATION
Fault System Observation Cause
Engine not starting or Ignition system Ignition spark is present Faulty fuel supply or compression system, mechanical defect
under difficulties No ignition spark STOP-switch operated, wiring fault or short circuit, spark plug or
connector defective, ignition module faulty
Fuel supply Fuel tank filled Incorrect choke position, carburetor defective, suction head (gas line
filter) dirty, fuel supply line bent or interrupted
Compression Inside of engine Cylinder bottom gasket defective, crankshaft seals damaged, cylinder or
piston rings defective
Outside of engine Improper sealing of spark plug
Mechanical
fault
Starter not engaging Broken starter spring, broken parts inside of the engine
Warm start problems Tank filled
Ignition spark existing
Carburetor contaminated, have it cleaned
Incorrect idling adjustment, suction head or carburetor contaminated Engine starts but dies
immediately
Fuel supply Tank filled
Fuel tank vent defective, fuel supply line interrupted, cable or
STOP-switch faulty
Insufficient
performance
Several
systems may
simultaneously
be affected
Engine idling Air filter contaminated, carburetor contaminated, muffler clogged,
exhaust duct in the cylinder clogged
Humidity
Drain fuel
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HTR 7610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HTR 7610 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info