78549

Makita HTR 5600 Manual

11
Zoom out
Zoom in
Previous page
1/86
Next page
11
OPERATION OF THE MACHINE
– Never operate with a loose grip.
– Never touch the cutting device when starting the engine and during
operation.
– Operate the Hedge Trimmer in such a manner as to avoid inhalation
of the exhaust gases. Never run the engine in enclosed rooms
(Risk of gas poisoning). Carbon monoxide is an odorless gas.
– All protective installations and guards supplied with the machine
must be used during operation.
– Never operate the engine with a faulty exhaust muffler or if it is
missing.
– Use the Hedge Trimmer only in good light and visibility.
During the winter season beware of slippery or wet areas, ice and
snow. (Risk of slipping.) Always ensure a safe footing .
– Never stand on a ladder and run the Hedge Trimmer. Keep both
feet on the ground.
– Never climb up the trees with the Hedge Trimmer to perform cutting
operation.
– Never work on unstable surfaces.
– Remove sand, stone, nails, wire, etc. found within the working area.
Foreign objects may damage the cutting blades.
– Before commencing cutting, the cutting blades must have reached
full working speed.
– Always hold the Hedge Trimmer firmly with both hands on the
handles only.
– The right hand grips the front handle of model HTR7610.
This is the way to safely operate the machine.
– Use a firm grip with thumbs and fingers encircling the handles.
– When you release the throttle, it takes a few moments before the
cutting blades stop.
– The Hedge Trimmer must not be used for cutting with fast idle. The
cutting speed cannot be adjusted with the throttle control in fast idle
position.
– When cutting a hedge, the machine should be held so that the blades
form a 15-30Ꮦangle with the cutting line.
– If the Hedge Trimmer is used with circular movements against the
edge of the hedge, the twigs will be thrown directly to the ground.
– At vertical cutting, the Hedge Trimmer is used with circular
pendulation, swinging up and down close to the hedge.
– Pay special attention when cutting hedges which are laid out a long a
wire-fence and have grown through the fence.
The blade must not contact the fence, otherwise the blades may be
destroyed.
– Do not use the Hedge Trimmer continuously for a long time. It is
normal to take a break of 10 to 20 minutes after every 50 minutes
operation.
– Should the cutting blades hit stones or other hard objects,
immediately switch off the engine and inspect the cutting blades for
damage. Replace damaged blades before re-commencing work.
– The engine must be switched off immediately in case of any engine
problems.
– Operate the Hedge Trimmer with as little noise and contamination as
possible. In particular check the correct setting of the carburetor
and the fuel/oil ratio.
– Do Not attempt to remove jammed cut material when blades are
running. Put unit down, turn it off, and remove necessary cuttings.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HTR 5600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HTR 5600 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info