691840

Makita HS6601 Manual

9
Zoom out
Zoom in
Previous page
1/72
Next page
9 ENGLISH
Switch action
WARNING: Before plugging in the tool,
always check to see that the switch trigger actu-
ates properly and returns to the "OFF" position
when released.
WARNING: NEVER defeat the lock-off button
by taping down or some other means. A switch with
anegatedlock-offbuttonmayresultinunintentional
operationandseriouspersonalinjury.
WARNING: NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button. A switch in need of repair
may result in unintentional operation and serious
personalinjury.ReturntooltoaMakitaservicecenter
forproperrepairsBEFOREfurtherusage.
►Fig.11: 1. Switch trigger 2.Lock-offbutton
Topreventtheswitchtriggerfrombeingaccidentally
pulled,alock-offbuttonisprovided.Tostartthetool,
depressthelock-offbuttonandpulltheswitchtrigger.
Releasetheswitchtriggertostop.
NOTICE: Do not pull the switch trigger hard
without pressing in the lock-off button. This can
causeswitchbreakage.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Removing or installing circular saw
blade
CAUTION: Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
CAUTION: Use only the Makita wrench to
install or remove the circular saw blade.
Toremovethecircularsawblade,presstheshaftlock
fullysothatthecircularsawbladecannotrevolveand
usethewrenchtoloosenthehexboltcounterclockwise.
Thenremovethehexbolt,ring(countryspecic),outer
angeandcircularsawblade.
►Fig.12: 1. Hex wrench 2. Shaft lock 3. Loosen
4. Tighten
For tool without the ring
►Fig.13: 1.Hexbolt2.Outerange3. Circular saw
blade4.Innerange
For tool with the ring
►Fig.14: 1.Hexbolt2.Outerange3. Circular saw
blade4.Ring5.Innerange
Toinstallthecircularsawblade,followtheremoval
procedure in reverse.
For tool with the inner ange for
other than 15.88 mm hole-diameter
saw blade
Theinnerangehasacertaindiameterprotrusionon
one side of it and a different diameter protrusion on the
other side. Choose a correct side on which protrusion
tsintothesawbladeholeperfectly.Mounttheinner
angeontothemountingshaftsothatthecorrectside
ofprotrusionontheinnerangefacesoutwardandthen
placesawbladeandouterange.
►Fig.15: 1. Mounting shaft 2.Innerange3. Circular
sawblade4.Outerange5.Hexbolt
WARNING: BE SURE TO TIGHTEN THE HEX
BOLT CLOCKWISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING: Make sure that the protrusion "a"
on the inner ange that is positioned outside ts
into the saw blade hole "a" perfectly. Mounting the
bladeonthewrongsidecanresultinthedangerous
vibration.
For tool with the inner ange for a
15.88 mm hole-diameter saw blade
(country specic)
Mounttheinnerangewithitsrecessedsidefacing
outward onto the mounting shaft and then place saw
blade(withtheringattachedifneeded),outerange
andhexbolt.
For tool without the ring
►Fig.16: 1. Mounting shaft 2.Innerange3. Circular
sawblade4.Outerange5.Hexbolt
For tool with the ring
►Fig.17: 1. Mounting shaft 2.Innerange3. Circular
sawblade4.Outerange5.Hexbolt
6.Ring
WARNING: BE SURE TO TIGHTEN THE HEX
BOLT CLOCKWISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING: If the ring is needed to mount the
blade onto the spindle, always be sure that the
correct ring for the blade's arbor hole you intend
to use is installed between the inner and the outer
anges.Useoftheincorrectarborholeringmay
resultintheimpropermountingofthebladecausing
blademovementandseverevibrationresultingin
possiblelossofcontrolduringoperationandinseri-
ouspersonalinjury.
Blade guard cleaning
Whenchangingthecircularsawblade,makesureto
alsocleantheupperandlowerbladeguardsofaccu-
mulated sawdust as discussed in the Maintenance
section. Such efforts do not replace the need to check
lowerguardoperationbeforeeachuse.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita HS6601 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita HS6601 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 10,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info