Manual Makita HS6601 (page 7 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691840

Zoom out

Zoom in

1/72

7 ENGLISH

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated(corded)powertoolorbattery-operated

(cordless) power tool.

Circular saw safety warnings

Cutting procedures

DANGER: Keep hands away from cutting

area and the blade. Keep your second hand

on auxiliary handle, or motor housing.Ifboth

handsareholdingthesaw,theycannotbecutby

theblade.

2. Do not reach underneath the workpiece. The

guardcannotprotectyoufromthebladebelowthe

workpiece.

3. Adjust the cutting depth to the thickness of

the workpiece.Lessthanafulltoothoftheblade

teethshouldbevisiblebelowtheworkpiece.

4. Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a

stable platform. It is important to support the

workproperlytominimizebodyexposure,blade

binding,orlossofcontrol.

►Fig.1

5. Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Contact with a "live" wire

will also make exposed metal parts of the power

tool "live" and could give the operator an electric

shock.

6. When ripping, always use a rip fence or

straight edge guide. This improves the accuracy

ofcutandreducesthechanceofbladebinding.

7. Always use blades with correct size and shape

(diamond versus round) of arbour holes.

Blades that do not match the mounting hardware

of the saw will run eccentrically, causing loss of

control.

8. Never use damaged or incorrect blade wash-

ers or bolt.Thebladewashersandboltwere

specially designed for your saw, for optimum

performance and safety of operation.

Kickback causes and related warnings

— kickbackisasuddenreactiontoapinched,bound

ormisalignedsawblade,causinganuncontrolled

saw to lift up and out of the workpiece toward the

operator;

— whenthebladeispinchedorboundtightlybythe

kerfclosingdown,thebladestallsandthemotor

reactiondrivestheunitrapidlybacktowardthe

operator;

— ifthebladebecomestwistedormisalignedinthe

cut,theteethatthebackedgeofthebladecandig

intothetopsurfaceofthewoodcausingtheblade

toclimboutofthekerfandjumpbacktowardthe

operator.

Kickbackistheresultofsawmisuseand/orincorrect

operatingproceduresorconditionsandcanbeavoided

bytakingproperprecautionsasgivenbelow.

1. Maintain a rm grip with both hands on the

saw and position your arms to resist kickback

forces. Position your body to either side of the

blade, but not in line with the blade.Kickback

couldcausethesawtojumpbackwards,but

kickbackforcescanbecontrolledbytheoperator,

if proper precautions are taken.

2. When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold

the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the

saw backward while the blade is in motion

or kickback may occur. Investigate and take

correctiveactionstoeliminatethecauseofblade

binding.

3. When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

bladeisbinding,itmaywalkuporkickbackfrom

the workpiece as the saw is restarted.

4. Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

tosagundertheirownweight.Supportsmustbe

placedunderthepanelonbothsides,neartheline

of cut and near the edge of the panel.

►Fig.2

►Fig.3

5. Do not use dull or damaged blades.

Unsharpenedorimproperlysetbladesproduce

narrowkerfcausingexcessivefriction,blade

bindingandkickback.

6. Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If

bladeadjustmentshiftswhilecutting,itmaycause

bindingandkickback.

7. Use extra caution when sawing into existing

walls or other blind areas.Theprotrudingblade

maycutobjectsthatcancausekickback.

8. ALWAYS hold the tool rmly with both hands.

NEVER place your hand, leg or any part of your

body under the tool base or behind the saw,

especially when making cross-cuts.Ifkickback

occurs,thesawcouldeasilyjumpbackwardsover

yourhand,leadingtoseriouspersonalinjury.

►Fig.4

9. Never force the saw. Push the saw forward at a

speed so that the blade cuts without slowing.

Forcing the saw can cause uneven cuts, loss of

accuracy,andpossiblekickback.

Lower guard function

1. Check lower guard for proper closing

before each use. Do not operate the saw if

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally

dropped,lowerguardmaybebent.Raisethe

lower guard with the retracting handle and make

sureitmovesfreelyanddoesnottouchtheblade

or any other part, in all angles and depths of cut.

2. Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use.

Lower guard may operate sluggishly due to

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita HS6601 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 10,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita HS6601 Manual

Product: